NextPVR Forums

Hi!
Is it possible to add support for Satelco EasyWatch PCI DVB-C?
I tried installing graphedit per instructions in the Wiki, but couldn't figure out how to start the program. Any help would be much appreciated.

10:38:50.774 INFO Log started
10:38:50.774 INFO Filter Check v1.0
10:38:50.774 INFO
10:38:50.774 INFO
10:38:50.774 INFO Checking AM_KSCATEGORY_CAPTURE filters
10:38:50.820 INFO found: Realtek HD Digital input
10:38:50.836 INFO - (output) Capture
10:38:50.836 INFO - (input) Input1
10:38:50.836 INFO
10:38:50.836 INFO
10:38:50.836 INFO
10:38:50.836 INFO Checking AM_KSCATEGORY_ENCODER filters
10:38:50.852 INFO
10:38:50.852 INFO
10:38:50.852 INFO Checking AM_KSCATEGORY_CROSSBAR filters
10:38:50.852 INFO
10:38:50.852 INFO
10:38:50.852 INFO Checking AM_KSCATEGORY_TVTUNER filters
10:38:50.852 INFO
10:38:50.852 INFO
10:38:50.852 INFO Checking AM_KSCATEGORY_TVAUDIO filters
10:38:50.852 INFO
10:38:50.852 INFO
10:38:50.852 INFO Checking AM_KSCATEGORY_VBICODEC filters
10:38:50.852 INFO
10:38:50.852 INFO
10:38:50.852 INFO Checking KSCATEGORY_BDA_NETWORK_TUNER filters
10:38:50.867 INFO found: Satelco EasyWatch PCI DVB-C Tuner (BDA)
10:38:50.867 INFO - (input) Input0
10:38:50.867 INFO - (output) Output1
10:38:50.867 INFO
10:38:50.867 INFO found: Satelco EasyWatch PCI DVB-C Tuner (BDA)
10:38:50.867 INFO - (input) Input0
10:38:50.867 INFO - (output) Output1
10:38:50.867 INFO
10:38:50.867 INFO
10:38:50.867 INFO
10:38:50.867 INFO Checking KSCATEGORY_BDA_RECEIVER_COMPONENT filters
10:38:50.867 INFO found: Satelco EasyWatch PCI DVB-C Tuner (BDA)
10:38:50.883 INFO - (input) Input0
10:38:50.883 INFO - (output) Output1
10:38:50.883 INFO
10:38:50.883 INFO found: Satelco EasyWatch PCI DVB-C Tuner (BDA)
10:38:50.883 INFO - (input) Input0
10:38:50.883 INFO - (output) Output1
10:38:50.883 INFO

Try adding this to your bda.ini file:

[Satelco EasyWatch DVB-C]
TUNING_TYPE=DVB-C
RECEIVER_ONLY_MODE=1
FILTER_RECEIVER=Satelco EasyWatch PCI DVB-C Tuner (BDA)
PIN_RECEIVER_IN=Input0
PIN_RECEIVER_OUT=Output1

Thanks for the quick reply!
It almost works. The device is detected when I choose "only show devices detected in this machine" in the Digital Source Configuration tool. I selected Finland/Helsinki-HTV as the location. When scanning for channels by clicking Map digital channels to EPG channels, I can hear and, at least some of the time, see the channels in the little preview screen, but the tool reports no channels are found.
I'll try playing with this again in the morning, seems like there must be an easy fix for this.

Do the scan, then zip and attach the config.exe.log and config.exe-native.log and I'll take a look.

There. There are three logs of each type, I think because I tried scanning three times.

Thanks a ton!

Quote:2008-12-21 00:16:35.555 VERBOSE FindFilterByName failed to locate filter: GB-PVR PSI Parser

Try running reregisterfilters.bat.

I suspect this wont help though, since it looks like you device failed to lock onto any signal. Was your cable provider in one of those listed? If not, you may need to create your own ini file, with correct frequencies and symbol rate for your cable channels.

I think that worked! Now it finds channels. I updated some drivers as well, so that might have affected the situation as well. Regardless, now it works. Great!