2005-02-02, 09:23 PM
Having problems with 0.908 with my Nova-T 90002
Here's the background:
Win XP Home SP2
P4 1.7
512Mb Ram
Hauppauge Nova-T 90002 with the latest Hauppauge 1.3 drivers.
Clean install of GBPVR on this machine, never had gbpvr on it before as I don't have an analogue TV capture card. Â Â Used to run gbpvr on my laptop to play mp3s throughmy MVP.
Installed ok.
In config, set BDA Recording Plug in, with correct region and transmitter in the Recording Source section.
EPG update ok with bleb.
After I hit Map digital channels to EPG channels button, first problem.
I get the warning box that I need to have the Cyberlink or Intervideo Mpeg2 Multiplexer filter installed.
Where can these codecs/filters be obtained from? Â I have installed the MPEG codec from the Hauppauge support page for the 90002. This didn't help. Â
Following other posts in the forum, I installed Cyberlink PowerDVD trial. That didn't seem to contain the filter I need either.
Need some guidance on that one.
Next, if I click past the warning and try to scan for channels, the scanning starts, then at the end, I get an unhandled exception. (See attached file for details) Â
About 1 time in 20 the scan is successful, and I get three TV channels and about 6 radio channels. Â (In the Hauppauge WinTV I get all the channels, both radio and TV)
I can then preview in the little window and assign these TV channels to EPG channels.
All ok(ish) so far, but when I start the app and try to view live TV, I get an "Error:Failure Playing Back File" message. Â I also get a mpeg file on the HDD in the recordings folder, size 0 bytes
As I said, I've tried to find the codecs. Â Need help on that one.
Can I not watch any TV at all without this codec issue sorted?
Will the codec issue be affecting my channel scan?
I've tried scanning All regions, All channels in the Capture source set up, but that never completes and I always get an unhandled exception. '0' is not a valid value for 'value' Â If I continue past the exception, nothing works in the config app, so I have to quit and try again.
I've also tried a complete reinstall, with no improvement.
Don't want to bother people with a dumb problem, but I am out of ideas on this one, and I can't see any suggestions in the forum.
Can't wait to get it all working, cos it all looks soooo good!
TIA,
Simon
Here's the background:
Win XP Home SP2
P4 1.7
512Mb Ram
Hauppauge Nova-T 90002 with the latest Hauppauge 1.3 drivers.
Clean install of GBPVR on this machine, never had gbpvr on it before as I don't have an analogue TV capture card. Â Â Used to run gbpvr on my laptop to play mp3s throughmy MVP.
Installed ok.
In config, set BDA Recording Plug in, with correct region and transmitter in the Recording Source section.
EPG update ok with bleb.
After I hit Map digital channels to EPG channels button, first problem.
I get the warning box that I need to have the Cyberlink or Intervideo Mpeg2 Multiplexer filter installed.
Where can these codecs/filters be obtained from? Â I have installed the MPEG codec from the Hauppauge support page for the 90002. This didn't help. Â
Following other posts in the forum, I installed Cyberlink PowerDVD trial. That didn't seem to contain the filter I need either.
Need some guidance on that one.
Next, if I click past the warning and try to scan for channels, the scanning starts, then at the end, I get an unhandled exception. (See attached file for details) Â
About 1 time in 20 the scan is successful, and I get three TV channels and about 6 radio channels. Â (In the Hauppauge WinTV I get all the channels, both radio and TV)
I can then preview in the little window and assign these TV channels to EPG channels.
All ok(ish) so far, but when I start the app and try to view live TV, I get an "Error:Failure Playing Back File" message. Â I also get a mpeg file on the HDD in the recordings folder, size 0 bytes
As I said, I've tried to find the codecs. Â Need help on that one.
Can I not watch any TV at all without this codec issue sorted?
Will the codec issue be affecting my channel scan?
I've tried scanning All regions, All channels in the Capture source set up, but that never completes and I always get an unhandled exception. '0' is not a valid value for 'value' Â If I continue past the exception, nothing works in the config app, so I have to quit and try again.
I've also tried a complete reinstall, with no improvement.
Don't want to bother people with a dumb problem, but I am out of ideas on this one, and I can't see any suggestions in the forum.
Can't wait to get it all working, cos it all looks soooo good!
TIA,
Simon
Simon, UK.
PVR 150, 80Gb and 250Gb SATA, UK Sky box as source.
PVR 150, 80Gb and 250Gb SATA, UK Sky box as source.