NextPVR Forums
  • ______
  • Home
  • New Posts
  • Wiki
  • Members
  • Help
  • Search
  • Register
  • Login
  • Home
  • Wiki
  • Members
  • Help
  • Search
NextPVR Forums Public NextPVR Support Windows v
1 2 3 4 5 … 114 Next »
"Device failed to lock a signal"

 
  • 0 Vote(s) - 0 Average
"Device failed to lock a signal"
Joram
Offline

Member

USA
Posts: 211
Threads: 21
Joined: Jul 2025
#1
2026-10-05, 09:08 PM (This post was last modified: 2026-10-05, 09:11 PM by Joram.)
My STB/Hauppauge HDPVR/NextPVR setup ran smooth as a cat's fur until this weekend when the MLB Division Series began. Throughout the baseball regular season, it worked so reliably that when it came time for the playoffs there was no thought of verifying the new recordings.

But when I looked this morning out of curiosity, I discovered that the weekend's playoff games had not recorded. The error message given in Web NPVR goes as follows:

[Failed: No errors, but no data delivered. This is usually because the device failed to lock a signal."]

When I try to tune a channel, the NPVR GUI displays either "please wait" (usually) or "Unable to find capture device" (once or twice).

Curiously, with the TV set to the TV's HDMI input for the STB, when I change channels via NPVR the new channel is displayed on the TV itself, but not on the laptop screen, where the NPVR GUI shows one of the above messages.

Hoping for a simple solution, I've taken the following steps:
  • Closing and relaunching NPVR.
  • Power-cycling the PC.
  • Power-cycling the HDPVR 2 1512.
  • Power-cycling the STB to which the HDPVR is connected.
None of this has helped.

Something seems to have happened somewhere along the device chain between October 1 (the date of the last successful recording) and October 3 (when the ALDS and NLDS started). I'm attaching the log file, in the hope that they will help someone knowledgeable about these things to pinpoint the cause of the problem.

Thank you in advance for any insights or suggestions.


Attached Files
.zip   logs-20261005-1459.zip (Size: 1.21 MB / Downloads: 2)
mvallevand
Online

Posting Freak

Ontario Canada
Posts: 57,066
Threads: 1,004
Joined: May 2006
#2
2026-10-05, 09:34 PM
Check with the Hauppauge software that you can record from the device. Maybe check cables to the splitter.

Your rules are messed up too, you tried to record it twice.

2026-10-04 19:58:00.132 [DEBUG][10] About to start recording (2555 on 21): D:\MediaPVR Public Videos\MLB Baseball\MLB Baseball_20261004_20002300.ts
2026-10-04 19:58:06.114 [DEBUG][10] About to start recording (2560 on 21): D:\MediaPVR Public Videos\MLB Baseball\MLB Baseball_20261004_20002300-0.ts

To tell you the truth I don't know if that does something to the drivers but I would definitely power off and wait after that.

Martin
Joram
Offline

Member

USA
Posts: 211
Threads: 21
Joined: Jul 2025
#3
2026-10-05, 10:21 PM
Thank you greatly, Martin. I've tried most of the suggestions and here are the notes:

The Hauppauge Capture software isn't working, either. Last week I could use it to view a recorded game from the DVR on the NPVR laptop, but this week it, too, is not working. Nor is WinTV managing to tune to a channel.

Checked all the HDMI cable connections starting from the STB, through the splitter, to the Hauppauge. Everything seems to be securely connected. Maybe disconnect and reconnect?

It looks like I might have set to record that October 4 game twice (whoops!). But then I'm not sure why recordings made prior to it might also fail.

Am currently installing Windows updates for the laptop, will try to tune a channel after it restarts.

Thanks again!
mvallevand
Online

Posting Freak

Ontario Canada
Posts: 57,066
Threads: 1,004
Joined: May 2006
#4
2026-10-05, 10:44 PM
You need to get the Hauppauge software working again so focus on that.

The double recordings wouldn't have caused a serious problem, just put things into an unknown state.

Martin
Joram
Offline

Member

USA
Posts: 211
Threads: 21
Joined: Jul 2025
#5
2026-10-05, 11:50 PM (This post was last modified: 2026-10-05, 11:51 PM by Joram.)
OK, I downloaded the latest version of Hauppauge Capture and installed it. (FWIW, did not see a download link for WinTV, although to be fair I was in a bit of a rush.)

After rebooting, there has been no improvement. WinTV gets "No signal," and Capture keeps claiming that it's detected the audio source has changed (??) and asks to reboot (for the umpteenth time).

The HDPVR2 itself appears to be working, as it lights up blue.
mvallevand
Online

Posting Freak

Ontario Canada
Posts: 57,066
Threads: 1,004
Joined: May 2006
#6
2026-10-06, 12:34 AM (This post was last modified: 2026-10-06, 12:57 AM by mvallevand.)
Take the HDPVR out of the equation and plug the HDMI out into your TV and make sure that still works.

Certainly yesterday and today there where issues where the HDPVR didn't see video

2026-10-04 19:58:01.873 [DEBUG][4] Device reports resolution(2): 0x0 (fps:0) (aspect:0) (progressive:1) (videoIdCode:0)

But Live TV appears to have worked after the reboot.

Martin
sub
Offline

Administrator

NextPVR HQ, New Zealand
Posts: 108,588
Threads: 786
Joined: Nov 2003
#7
2026-10-06, 01:12 AM
Yeah, try that HDMI into a TV. If it works, they may have turned on HDCP on the set top box. ie content protection. A way around that is using one of the HDMI splitters that conveniently also remove HDCP.
Joram
Offline

Member

USA
Posts: 211
Threads: 21
Joined: Jul 2025
#8
2026-10-06, 06:19 AM
(2026-10-06, 12:34 AM)mvallevand Wrote: Take the HDPVR out of the equation and plug the HDMI out into your TV and make sure that still works.

Certainly yesterday and today there where issues where the HDPVR didn't see video

2026-10-04 19:58:01.873 [DEBUG][4] Device reports resolution(2): 0x0 (fps:0) (aspect:0) (progressive:1) (videoIdCode:0)

But Live TV appears to have worked after the reboot.

Martin

Martin, thanks for the idea. Before I proceed, I want to make sure that I end up doing what you're asking.

I already have one HDMI wire coming out of the HDMI splitter and right into the TV, while the other one coming out of the splitter goes into the Hauppauge. The cable that currently goes to the TV displays fine onscreen, so I'll unplug it from the TV's HDMI port and replace it with the cable that's being used for the Hauppauge. For good measure, I'll plug the other HDMI cable into the Hauppauge and see if WinTV starts working.

It's getting late around here, so I'll do that tomorrow (Tuesday). With any luck, it'll be something as simple as an HDMI cable that went bad.
mvallevand
Online

Posting Freak

Ontario Canada
Posts: 57,066
Threads: 1,004
Joined: May 2006
#9
2026-10-06, 12:45 PM
If you have the STB configured for auto output there could be a conflict with two inputs, if it is not a manual selection. If it is manual you are bound to have trouble

There could also be a conflict if the tuning is slow when you change channels which would also explain the fps (0,0) problem. If the STB output is auto change it to fixed audio and video 1280x720 will produce smaller files and you may not notice the difference.

If you want to feed the TV I would feed from the passive output from the HDPVR not the splitter. I'd still use fixed output.

Martin
Joram
Offline

Member

USA
Posts: 211
Threads: 21
Joined: Jul 2025
#10
2026-10-06, 04:33 PM
Martin, thank you for the answer but I'm not fluent in AVese ? so I'm going to need some translation/explanation there. Up until today, for months I had made no changes to settings or hardware anywhere along the line. So in theory at least, there should be no need to fiddle with settings, unless somehow they can change without user input?

What I did do today was to switch the HDMI cables coming out of the splitter, such that the cable that was going to the TV is now going to the HDPVR, while the cable that was going to the HDPVR is now going to the TV. As the result is that I'm still getting a signal to the TV but not to the HDPVR, this suggests that the problem isn't the HDMI cables.

Before switching where the cables went to, I had also switched the HDMI ports that each was coming out of from the splitter. That made no difference. So it's not a problem with the ports on the splitter, either. Then I put the cables back to their original ports on the splitter and instead switched where they led to, as described in the paragraph just above this one.

All of the above was done with all of the equipment involved either turned off or disconnected from power before unplugging HDMI cables.

Returning to your reply -- when you say...

Quote:If you want to feed the TV I would feed from the passive output from the HDPVR not the splitter. I'd still use fixed output. 

...what do "passive output" and "fixed output" mean?

I also don't know what is meant by manual vs. auto output selection. Though as I said, I haven't tinkered with the STB settings in months so I don't understand why an output selection setting would come into play now.
« Next Oldest | Next Newest »

Users browsing this thread: 2 Guest(s)

Pages (5): 1 2 3 4 5 Next »


Possibly Related Threads…
Thread Author Replies Views Last Post
  Message "ecording failed" but it actually worked srochford 1 37 4 hours ago
Last Post: mvallevand
  [Failed: No errors, but no data delivered. This is usually because the device failed Petrovski 2 405 2026-11-07, 10:45 AM
Last Post: Petrovski
  Channels not detected in device scanning Higgo 5 4,208 2026-08-28, 03:57 AM
Last Post: mvallevand
  Default admin and password login failed m1ctk 2 779 2026-06-15, 09:16 PM
Last Post: m1ctk
  NPVR UI not picking up TV signal Joram 9 1,553 2026-03-15, 10:06 PM
Last Post: Joram
  Next PVR stopped working - Streaming Failed - HD HomeRun weavol 6 1,359 2026-02-22, 02:48 AM
Last Post: weavol
  NextPVR status says device is recording when it is not FrogFan 4 1,101 2026-01-17, 12:30 AM
Last Post: FrogFan
  Had tuner problems, many failed recordings bass_gas 5 1,408 2026-01-01, 09:10 PM
Last Post: bass_gas
  Streaming Failed (transcoder exited) Fender_Bender66 5 1,555 2025-11-12, 05:40 PM
Last Post: mvallevand
  EPG wont update, device not correct, channels won't import LateNightCat 7 1,793 2025-11-07, 05:31 PM
Last Post: mvallevand

  • View a Printable Version
  • Subscribe to this thread
Forum Jump:

© Designed by D&D, modified by NextPVR - Powered by MyBB

Linear Mode
Threaded Mode