DVB-S2 Scanning not working after 1.5.31

[agerdin]

sub, logs from the latest scans attached.

\\Agerdin

[sub]

It looked like it did everything it needed to.

Do the modulation/pilot/rolloff values below match the transponder you're trying to scan? ie 8PSK, 0 (pilot off), 0.35,

Code:

<tuning>
  <type>DVB-S</type>
  <locator>
    <frequency>10934</frequency>
    <polarity>H</polarity>
    <symbol_rate>25000</symbol_rate>
    <fec>34</fec>
    <diseqc_type>1</diseqc_type>
    <lnb>1</lnb>
    <lowosc>9750</lowosc>
    <highosc>10600</highosc>
    <switch>11700</switch>
    <modulation>8PSK</modulation>
    <rolloff>0.35</rolloff>
    <pilot>0</pilot>
  </locator>
</tuning>

[agerdin]

It looked like it did everything it needed to.

Do the modulation/pilot/rolloff values below match the transponder you're trying to scan? ie 8PSK, 0 (pilot off), 0.35,

Code:

<tuning>
  <type>DVB-S</type>
  <locator>
    <frequency>10934</frequency>
    <polarity>H</polarity>
    <symbol_rate>25000</symbol_rate>
    <fec>34</fec>
    <diseqc_type>1</diseqc_type>
    <lnb>1</lnb>
    <lowosc>9750</lowosc>
    <highosc>10600</highosc>
    <switch>11700</switch>
    <modulation>8PSK</modulation>
    <rolloff>0.35</rolloff>
    <pilot>0</pilot>
  </locator>
</tuning>

sub, I hope my values are correct. They were not so easy to find but the extract below if from my satelite provider.

Code:

"Satellite: THOR 6
Transponder: A16
Downlink frequency: 10934 MHz
Downlink polarisation: Horisontal
Symbol rate: 25,0 Msym/sec
Forward Error Correction: 3/4
DVB-S2, 8PSK, Pilot OFF"

This is all information I got and the same values results in channels found in PVRX2.

\\Agerdin

[agerdin]

sub, do you have any more ideas? I am about to start over with a fresh install of NPVR to see if it helps.

I understand that you have it working with your HVR-4400 card?

\\Agerdin

[sub]

Can you create a c:\temp directory, and set HKEY_LOCAL_MACHINE\Software\NPVR\LogTSFlow=1 (DWORD) (HKEY_LOCAL_MACHINE\Software\Wow6432Node\NPVR\LogTSFlow=1 on 64bit version of Windows), then start the app then scanning again, then post the c:\temp\mon.txt file?

[agerdin]

sure, mon log file attached.

\\Agerdin

[sub]

Hmm, it looks like its locking on to the signal, and receiving data. Let me think about it for a few minutes...

[agerdin]

Ok, that was beyond my knowledge

Is there anything I can do to help now?

\\Agerdin

[sub]

Actually thinking again, did you scan just DVB-S2 frequencies then, or did you also scan a DVB-S frequency?

[agerdin]

Both, my test file includes one S frequency and one S2 frequency. Do you want me to do a clean scan with only S2 frequency?

Code:

[SATTYPE]
1=3592
2=Thor 6 CD, HD TEST

[DVB]
0=2
1=10809,V,24500,78
2=10934,H,25000,34,38

\\Agerdin