EmuNation

observer_11 · 2008-05-17, 09:11 PM

Agarwal's v1.1.6.0 version should work fine with Emunation. Make sure you have the filter registered (regsvr32 mdapifilter.ax). I believe you also need FFDecsa.dll and pthreadVC2.dll in the gbpvr directory.

jasonpv · 2008-05-18, 06:48 AM

Do you know where to get Agarwal's v1.1.6.0 observer? Which gbpvr folder does this need to be placed in?

observer_11 · (This post was last modified: 2008-05-18, 08:07 PM by observer_11.)

Quote:Do you know where to get Agarwal's v1.1.6.0 observer?

See attached.

Quote:Which gbpvr folder does this need to be placed in?

GBPVR folder.

soccerdad · 2008-05-18, 03:55 PM

The filter needs to go into the gbpvr folder and it needs to be registered, the plugin goes in the mdplugin folder.

observer_11 · 2008-05-18, 08:05 PM

soccerdad Wrote:The filter needs to go into the gbpvr folder and it needs to be registered, the plugin goes in the mdplugin folder.

My bad, soccerdad is correct.

arkennedy75 · 2008-05-18, 11:58 PM

how do you register the mdapifilter.ax filter? When I run "Re-Register Filters.bat" it doesn't appear to register mdapifilter. Is there something else I should be doing? Thanks.

***sub*** · 2008-05-19, 12:07 AM

Its not part of GB-PVR so Re-RegisterFilters.bat wont register it. You'd need to manually register it by running "regsvr32 c:\path\to\mdapifileter.ax"

NI2O · 2008-05-19, 03:26 AM

Thanks to all on this thread I've been kinda sorta able to get this going on my setup (was using a Pansat sm20 via the svideo port until now).

I have a small issue however; I can't see any pictures. Sound for the $$$ channels is fine just no pix.

I'm using a Twinhan 1020 into a 4 port diseqc switch with a set of 4 fixed dishes pointed at nimiq1, nimiq 2, Echostar 3 and Galaxy 25.

I CAN see the clear picture from Echostar 3 on channel "D61.5". Just none of the $$$ ones.

I get the signal bar pop up complaining that it's been too long since it issued the tuning instructions.

Any ideas?

Thanks

Mark

bigdawgte · 2008-09-17, 02:10 PM

I am just yesterday getting back to GBPVR after a several year hiatus. In the meantime, I have been using Emu* for D119, D110 and sometimes BEV92. I seem to have gotten the MDAPI architechture up and running using Team Mediaportal - I can get the familiar Emu* screen rolling as with DVBDream and MyTheatre. However, I can't tune to any of the dvb channels (my ATSC channels are doing fine - two cards FusionHDTV ATSC and Twinhan 1022a) from within PVRX2 - the tv window crashes back to the main menu before any of the dvb-s channels can tune. In config, when I try to map channels or update the epg, as I watch the emu* console, I believe that the the tuning times out before emu* can unlock.

1. Is GBPVR/PVRX2 exhibiting proper behavior? Or should I be able to tune a channel before d...n?
2. Am I following the proper procedure?

***sub*** · 2008-09-17, 03:51 PM

Quote:However, I can't tune to any of the dvb channels (my ATSC channels are doing fine - two cards FusionHDTV ATSC and Twinhan 1022a) from within PVRX2 - the tv window crashes back to the main menu before any of the dvb-s channels can tune.

Reproduce the problem, then zip and attach the logs and I'll take a look.