No signal with the HVR1100

[Gareth2061]

I have everything set up properly but when i select 'watchliveTV' I get told that there is no signal.

here is a screenshot of the problem.

The thing is, it works fine under the Hauppague software.

[sub]

Zip and attach the logs and I'll take a look.

[hastar]

I also have this problem. When it scans for channels it shows a preview, but when i open GB-PVR to watch tv I get the same image as above

Logs attached

edit: Oops forgot to metion version number 1.0016

[NumberFive]

I also have this exact same problem with a Nova-T SE stick (type 3 in BDA.ini).

I've also noticed the EPG update hangs on the second multiplex it trys sometimes.

[wharrad]

I've just started getting this problem following the update. Works fine with the MegaSky sticks but not the HVR 1100 (well, 1110 really).




(quick thanks to Sub for the excellent software! - there are always too many things we're bugging him about!)

[hastar]

I've just been looking through the BDA.ini and noticed that the section for HVR-1100 is as follows:
[Hauppauge HVR-1100]
TUNING_TYPE=DVB-T
FILTER_TUNER=Hauppauge WinTV-HVR 73XX BDA DVBT Tuner
FILTER_CAPTURE=Hauppauge WinTV-HVR 73XX BDA Digital Capture
PIN_TUNER_IN=Input0
PIN_TUNER_OUT=MPEG2 Transport
PIN_CAPTURE_IN=MPEG2 Transport
PIN_CAPTURE_OUT=MPEG2 Transport

However my 1100 driver is labelled 67XXX BDA DVBT Tuner in device manager and the Hauppage prodinfo program shows this:

Model 67019 Rev. B1B4
Serial #4028020983
Tuner Model/Formats: Philips 8275A // (MN/BG/I/DK/LL') / DVB-T
Tuner Audio: Stereo (SAA7131)
Video Formats: NTSC ( M ) PAL ( B G H I D K M N NCOMBO ) SECAM ( L L' )
Audio Outputs: None
External Inputs: 2
S-Video Inputs: 2
Teletext:
Radio: FM
Decoder: SAA7131
IR: Blaster
MAC Address: 00-0D-FE-16-B8-F7

EEprom Contents:
84 09 00 04 20 77 00 40 f7 b8 16 f0
73 05 29 00
84 08 00 06 cb 05 01 00 94 18 89
72 07 70
73 09 23 5f
73 0a fc 72
72 0b 2f
72 0e 01
72 0f 03
72 10 01
72 11 ff
79 a9

hcwI2C32.DLL 2.28.25019
hcwPNP32.DLL 4.76.25102
hcwChDB.dll 2, 2, 25092, 0
HCWChMgr.ocx 2, 1, 25102, 0
hcwTVDlg.DLL 3.16.21311
hcwTVWnd.DLL 3, 02, 25102 PCI-USB DVBT/S PVR
hcwUtl32.DLL 3.8.22159
hcwSplit.ax 1.15.24235
hcwFRead.ax 1, 16, 23294, 0
hcwFWrit.ax 1, 15, 24044, 0
hcwSnap.ax 1.14.24335


a bit more research shows that this card is a HVR-1110, this is a bit confusing as I have the box here and it def says 1100.....

Is this a possible driver mix match? I have tried selecting the hp DVB-T Nova driver but that shows as 'card not recognised' .

[sub]

Can you run FilterCheck then attach the resulting FilterCheck.log: http://forums.gbpvr.com/showpost.php?p=1...ostcount=6. I'll check the names are correct for your drivers.

[hastar]

here is the filter check log

looking at the drivers actually installed hcw713x.sys is installed. Also my old conextant card installed a ton of devices, crossbar, etc. this card only has one entry.....

attached;filterchecklog;inf file that installs the drivers FYO

[sub]

Does ths help?

[Hauppauge HVR-1100 type2]
TUNING_TYPE=DVB-T
FILTER_TUNER=Hauppauge WinTV-HVR 713X BDA DVBT Tuner
FILTER_CAPTURE=Hauppauge WinTV-HVR 713X BDA Digital Capture
PIN_TUNER_IN=Input0
PIN_TUNER_OUT=MPEG2 Transport
PIN_CAPTURE_IN=MPEG2 Transport
PIN_CAPTURE_OUT=MPEG2 Transport

[hastar]

Nope, sorry. When i make the cange it says, failed to start BDA device as it cannot be found.