I can't find any SAT channels with my 2x hauppauge HVR4000.
With CyberLink PowerCinema 5.1 (came with HVR4000 card) i can find and watch every channel incl. HD channels.
When i press "Map digital channels to EPG channels" then i get a messagebox "DirectVobSub: IPersistStream is no longer supported" after some seconds.
Then GB-PVR scans for channels but can't find any.
I Attached all logs.
Please help.
Here my configuration:
PC:
Motherboard P5GDC-V Deluxe
2x Hauppauge HVR4000
P4 2,8 GHz
1GB RAM
MSI NX7900GS (T2D256EZ)
SATA HDs
WinXP SP2
GB-PVR v1.1.5
--------------------------------------------------------------------------
LNB:
Inverto Universal Quattro IDLP-401QTL+
http://www.inverto.tv
Input Frequency (GHz): 10.7-11.7, 11.7-12.75
L.O Freq (GHz): 9.75/10.6
Polarization: Linear
Accur.&stab.+Mhz (@25C): +/- 1
LNB Gaint (typ.) dB: 50-65
Gain Flatness: 0.75dB@36MHz max
7db@IF p-p max
Pol. & Freq. Band control: 13/18v 22Khz (standard)
Gain Stability: N/A
Phase Noise (dBc/Hz): @ 1 KHz - 50
@ 10 KHz - 75
@ 100 KHz -95
Image Rejection (dBm): -40
Spurious (dBc): -60
1db compr. Point (min., dBm): 0
Output Connector: 75 ohm - "F" Female
Operation Temerature (oC): -30 to +60
F/D of feed: 0.6 - 0.7
--------------------------------------------------------------------------
Multiswitch 6x:
Spaun SMS 5602 NF
http://www.spaun.de
--------------------------------------------------------------------------
GB-PVR Capture Source Settings:
Both HVR4000 configured equal.
Recording Source: BDA Recording Plugin
EPG Source: configured and imported
Channel Changer: No Channel Changer Required
--------------------------------------------------------------------------
Settings of BDA Recording Plugin:
Device Type: Hauppauge HVR-4000 (DVB-S/S2)
Type: DVB-S
Country: All Countries
Region/Transm.: Astra 1E, 1F, 1G, 1H, 1KR, 2C
LNB LOF1 (MHz): 9750
LNB Switch (MHz): 11700
LNB LOF2 (MHz): 10600
Powerd: yes
DiSEqC: NONE
BDA Advanced Settings: default (none checked)
With CyberLink PowerCinema 5.1 (came with HVR4000 card) i can find and watch every channel incl. HD channels.
When i press "Map digital channels to EPG channels" then i get a messagebox "DirectVobSub: IPersistStream is no longer supported" after some seconds.
Then GB-PVR scans for channels but can't find any.
I Attached all logs.
Please help.
Here my configuration:
PC:
Motherboard P5GDC-V Deluxe
2x Hauppauge HVR4000
P4 2,8 GHz
1GB RAM
MSI NX7900GS (T2D256EZ)
SATA HDs
WinXP SP2
GB-PVR v1.1.5
--------------------------------------------------------------------------
LNB:
Inverto Universal Quattro IDLP-401QTL+
http://www.inverto.tv
Input Frequency (GHz): 10.7-11.7, 11.7-12.75
L.O Freq (GHz): 9.75/10.6
Polarization: Linear
Accur.&stab.+Mhz (@25C): +/- 1
LNB Gaint (typ.) dB: 50-65
Gain Flatness: 0.75dB@36MHz max
7db@IF p-p max
Pol. & Freq. Band control: 13/18v 22Khz (standard)
Gain Stability: N/A
Phase Noise (dBc/Hz): @ 1 KHz - 50
@ 10 KHz - 75
@ 100 KHz -95
Image Rejection (dBm): -40
Spurious (dBc): -60
1db compr. Point (min., dBm): 0
Output Connector: 75 ohm - "F" Female
Operation Temerature (oC): -30 to +60
F/D of feed: 0.6 - 0.7
--------------------------------------------------------------------------
Multiswitch 6x:
Spaun SMS 5602 NF
http://www.spaun.de
--------------------------------------------------------------------------
GB-PVR Capture Source Settings:
Both HVR4000 configured equal.
Recording Source: BDA Recording Plugin
EPG Source: configured and imported
Channel Changer: No Channel Changer Required
--------------------------------------------------------------------------
Settings of BDA Recording Plugin:
Device Type: Hauppauge HVR-4000 (DVB-S/S2)
Type: DVB-S
Country: All Countries
Region/Transm.: Astra 1E, 1F, 1G, 1H, 1KR, 2C
LNB LOF1 (MHz): 9750
LNB Switch (MHz): 11700
LNB LOF2 (MHz): 10600
Powerd: yes
DiSEqC: NONE
BDA Advanced Settings: default (none checked)