Followed install instructions- No go

[zaldwaik]

Yesterday you re-configured GBPVR to not AutoStart an MVP Server

getValue: /settings/MVPServerAutostart : 0

Martin

This is a new install before I installed mvp, that was the default, I will change it and see how it works.

[mvallevand]

You must have done a new GBPVR install after running NMTInstall, because there are also entries where it was running.

2009-11-24 20:30:16.062 VERBOSE [4] getValue: /settings/MVPServerAutostart : 1

Martin

[mvallevand]

Looking at your config.xml. You don't have your MAC address or you the Web Server enabled. Did you even run NMTInstall?

Martin

[zaldwaik]

I had gbpvr installed, then installed NMT, I unchecked the gbpvr, and gbpvr updates as I had the latest gbpvr. Should I reinstall? Where would the MAC address be, and what web server?

[mvallevand]

What I think happened is you opened config.exe made some changes and then

Code:

2009-11-24 20:19:32.421    VERBOSE    [1]    getValue: /settings/PostShowPadding : 2
2009-11-24 20:19:32.593    VERBOSE    [1]    CustomTaskSettings.loadAll()
2009-11-24 20:34:32.046    INFO    [1]    Config is saving settings
2009-11-24 20:34:32.125    INFO    [1]    ...saving to disk

and ran NMTInstall while config was open

2009-11-24 20:29:58.796 INFO [4] GB-PVR Recording Service starting

When you saved your settings in config.exe you lost the NMT settings.

I would untick everything in NMTInstall except "Configure GBPVR PCH Setting." Use 001B2FE0A5A8 as the MAC address when prompted.

Martin

[zaldwaik]

You are right and a genius! It works. I was able to watch TV on my PCH with little delay.

Two little things, where would I find remote mappings (is it possible to change?) and is there a way to get out of a "PCH freezes not sure what is happening" situation without rebooting PCH?

Thanks a lot.

[mvallevand]

The remote reference is linked on the wiki http://www.mvpmc.org/~mvallevand/nmtkeys.html

I have no idea what the "PCH freezes not sure what is happening" problem is. It worries me when anyone uses a wireless network but the only real issue in mvpmcx2 in 1.4.7 that I am aware of is the gbpvr bug after watching two livetv shows in a row. Open a new thread and upload your logs and describe the problem and I'll see if I can help.

Martin

[zaldwaik]

Thanks a lot. I have added the share per directions (I only put the URL and it assigned the right name) I can get to the html page, but none of the options work (I get an error from PCH). It works fine if I browse to it. Oh, well, not critical, but would be nice if it works.

[mvallevand]

Did you power off to reset your PCH first? If so send the information from the NMT syntax checker once again. You are too close to stop now.

Martin

[zaldwaik]

Sorry, same issue after recycling PCH.

Checking for mvpmc share on PVR
mvpmc f:\mvpmc

Checking GB-PVR.html links
<a href="http://localhost.drives:8883/NETWORK_SHARE/PVR:mvpmc/gbpvr.cgi">GB-PVR</a>
<a href="http://localhost.drives:8883/NETWORK_SHARE/NETWORK_BROWSER/browser.cgi">GB-PVR via Network Browser</a>
<a href="http://localhost.drives:8883/USB_DRIVE_A-1/mvpmc/usb_a.cgi">GB-PVR via USB</a>

NMT IP Address: 192.168.1.9 MAC 001B2FE0A5A8

GB-PVR Installed c:\Program Files\Devnz\GBPVR\
config.xml entry found Client Type PCH2

Checking NMT Version
01-17-091022-15-POP-403-000

Checking NMT Display
1080p 60Hz

Calling NMT Source
pvr:mvpmc
smb://pvr/mvpmc Username: Password Length: 0