Sub,
I generally never use Live TV, so I had not tested it with Npvr up until this point. After additional testing, it looks like Live TV will always work the first time (after a reboot or restart of Nrecord). If I escape out of Live TV and then restart it, I get the error "Unable to Communicate with Recording Service". Any further attempts will then report the error "Failed to Start Stream". I have attached log files that reflect trying to start Live TV 4 successive times immediately after a reboot of the system.
I still think it must have something to do with my HDHR setup, but for the life of me I cannot figure out what it could be. There are not that many options to configure, and no options when installing the drivers. Seems like the tuners are not reallocating or something? Anyway, hopefully these logs will show something.
It appears when it works, the log shows the following:
When it fails, I get this (a number of steps are missing after the line "About to auto detect capture filter":
I generally never use Live TV, so I had not tested it with Npvr up until this point. After additional testing, it looks like Live TV will always work the first time (after a reboot or restart of Nrecord). If I escape out of Live TV and then restart it, I get the error "Unable to Communicate with Recording Service". Any further attempts will then report the error "Failed to Start Stream". I have attached log files that reflect trying to start Live TV 4 successive times immediately after a reboot of the system.
I still think it must have something to do with my HDHR setup, but for the life of me I cannot figure out what it could be. There are not that many options to configure, and no options when installing the drivers. Seems like the tuners are not reallocating or something? Anyway, hopefully these logs will show something.
It appears when it works, the log shows the following:
Code:
2010-07-30 09:14:23.740 [DEBUG][5] StartStream(7173:WLWT-HD)
2010-07-30 09:14:23.753 [INFO][5] DigitalRecorder.StartStream(LIVE&C:\Temp\live-WLWT-HD-3401.ts)
2010-07-30 09:14:23.753 [INFO][5] Creating BDA graph
2010-07-30 09:14:23.904 [DEBUG][5] Using tuner Silicondust HDHomeRun Tuner 10117487-0 (1)
2010-07-30 09:14:23.959 [DEBUG][5] About to auto detect capture filter
2010-07-30 09:14:24.249 [DEBUG][5] No BDA capture filter for this device
2010-07-30 09:14:24.357 [DEBUG][5] Graph filter list:
2010-07-30 09:14:24.357 [DEBUG][5] - BDA MPEG2 Transport Information Filter
2010-07-30 09:14:24.357 [DEBUG][5] - MPEG-2 Demultiplexer
2010-07-30 09:14:24.357 [DEBUG][5] - NPVR TS Mon
2010-07-30 09:14:24.357 [DEBUG][5] - Tuner
2010-07-30 09:14:24.357 [DEBUG][5] - Network Provider
2010-07-30 09:14:24.361 [INFO][5] About to start BDA graph
2010-07-30 09:14:24.363 [DEBUG][5] Starting graph...
2010-07-30 09:14:24.367 [DEBUG][5] About to tune BDA graph:
<tuning>
<type>ATSC</type>
<locator>
<physical_channel>35</physical_channel>
</locator>
<service_id>1</service_id>
<tsid>2243</tsid>
<service_type>1</service_type>
</tuning>
2010-07-30 09:14:25.701 [DEBUG][5] locked=1, present=1, strength=95, quality=97 (took 1185ms to check)
2010-07-30 09:14:25.732 [INFO][5] DigitalRecorder.StartStream() allocated handle: 0x1
2010-07-30 09:14:25.743 [DEBUG][5] Live TV handle: 0x140001
2010-07-30 09:14:25.792 [DEBUG][13] GetQuality()
2010-07-30 09:14:25.792 [DEBUG][13] GetQuality()@exit
...
When it fails, I get this (a number of steps are missing after the line "About to auto detect capture filter":
Code:
2010-07-30 09:14:52.240 [DEBUG][13] StartStream(7173:WLWT-HD)
2010-07-30 09:14:52.240 [INFO][13] DigitalRecorder.StartStream(LIVE&C:\Temp\live-WLWT-HD-3402.ts)
2010-07-30 09:14:52.240 [INFO][13] Creating BDA graph
2010-07-30 09:14:52.247 [DEBUG][13] Using tuner Silicondust HDHomeRun Tuner 10117487-0 (1)
2010-07-30 09:14:52.285 [DEBUG][13] About to auto detect capture filter
2010-07-30 09:14:52.937 [DEBUG][13] GetQuality()
2010-07-30 09:14:52.937 [DEBUG][13] GetQuality()@exit
2010-07-30 09:14:53.952 [DEBUG][13] GetQuality()
...