2013-10-25, 07:29 PM
:confused:
Thanks for viewing the thread, and any advice you can give. Here's my situation (specs first):
OS: Server 2008 R2 (Dedicated machine for this PVR purpose)
- Desktop Experience feature added
- Hack/batch for BDA devices used
- Direct X web redist installed
- VLC installed
- Shark007 Codec Pack installed (ffmpeg used for most decoders)
Core 2 Quad, 8GB RAM, Nvidia Chipset, Quadro FX3800, Dual Gigabit Ethernet (might team them later)
Tuners:
HDHR Prime (w/Cisco Cable Card from TWC)
Asus EHD3100 (not connected to cable yet)
Hauppauge WinTV PVR PCI II (not connected to cable yet nor detected by NPVR)
Please let me know if any of the prior installed software is unnecessary and I'll gladly remove it. So I've set up NPVR 3.1.1 and gotten the HDHR detected, as DCR-2650, and the channels populated. Using the OTA EPG for now. No plugins except TV Guide, Live TV, Recordings, and Search on the server client. Planning on Using XBMC as the remote clients with the NextPVR plugin. I've set a CNAME in DNS to point "TV" to the PVR Server, so for all entries I use TV as the host name. I've specifically shared the NPVR, Record and Temp folders for read only to authenticated users, so clients can see and connect to \\TV\*folder*. I've allowed, both receive and transmit, all of the .exe required and even a couple extra trough the firewall.
The issue I ran into that I can't seem to get past is two part I think, but maybe two parts of the same thing. First is that I can't seem to get clients to receive the stream from NPVR, even the client on the server doesn't seem to be able to get the stream. I see in Status that the Device starts a *.ts and the Tray icon turns red, but in about 30 sec it stops and the icon goes to normal again. I've attached logs from a couple attempts. The second issue is the web guide doesn't populate any TV Guide data.
Any help would be greatly appreciated. Thank you
Thanks for viewing the thread, and any advice you can give. Here's my situation (specs first):
OS: Server 2008 R2 (Dedicated machine for this PVR purpose)
- Desktop Experience feature added
- Hack/batch for BDA devices used
- Direct X web redist installed
- VLC installed
- Shark007 Codec Pack installed (ffmpeg used for most decoders)
Core 2 Quad, 8GB RAM, Nvidia Chipset, Quadro FX3800, Dual Gigabit Ethernet (might team them later)
Tuners:
HDHR Prime (w/Cisco Cable Card from TWC)
Asus EHD3100 (not connected to cable yet)
Hauppauge WinTV PVR PCI II (not connected to cable yet nor detected by NPVR)
Please let me know if any of the prior installed software is unnecessary and I'll gladly remove it. So I've set up NPVR 3.1.1 and gotten the HDHR detected, as DCR-2650, and the channels populated. Using the OTA EPG for now. No plugins except TV Guide, Live TV, Recordings, and Search on the server client. Planning on Using XBMC as the remote clients with the NextPVR plugin. I've set a CNAME in DNS to point "TV" to the PVR Server, so for all entries I use TV as the host name. I've specifically shared the NPVR, Record and Temp folders for read only to authenticated users, so clients can see and connect to \\TV\*folder*. I've allowed, both receive and transmit, all of the .exe required and even a couple extra trough the firewall.
The issue I ran into that I can't seem to get past is two part I think, but maybe two parts of the same thing. First is that I can't seem to get clients to receive the stream from NPVR, even the client on the server doesn't seem to be able to get the stream. I see in Status that the Device starts a *.ts and the Tray icon turns red, but in about 30 sec it stops and the icon goes to normal again. I've attached logs from a couple attempts. The second issue is the web guide doesn't populate any TV Guide data.
Any help would be greatly appreciated. Thank you