Hello everyone,
Lately I have been noticing that my IPTV channels have been acting up where the channel would start then a minute in it would either freeze or restart the stream from where I started. This was happening on all my devices no matter being NextPVr or tivimate Etc. I then had found that my Mothers NextPVR was the culprit. She had been for whatever reason Probably being 80 years old and just pushing buttons started a reoccurring recording on a program 7 yes 7 times concurrently. My IPTV provider only allows me 5 connections. With this being said I went in and deleted all of her reoccurring and pending recordings thinking this would take care of the problem. This should have solved the problem for nothing was scheduled to record and none of the timelines in the EPG were red.
I did all the usual scans such as antivirus, Antimalware and running bleachbit with none of these resulting in any issues or resolving the problem. I then did a reboot of the modem, router and rebooted the PC. This seems to have solved the issue.
Can someone tell me their thoughts on this one?
Thank you,
Bruce
Quote:New streaming service Freely is set to become the online successor to Freeview. It will allow viewers to stream all major TV channels without an aerial or satellite dish.
The service will launch in 2024, but will require a next-generation smart TV.
I wonder if NextPVR will be able to access it, or will it be locked down to the next generation smart TVs which come on sale in 2024?
I installed a Docker container with NextPVR on my QNAP NAS. I am able to record TV channels but I am unable to watch any TV channel : I get an error message at the bottom of the screen in red: "Streaming Failed (transcoder exited)". Here's the log information. I use a SiliconDust HDHomeRun dual-tuner. Could you help me, please?
There is an app for TvHeadEnd called antennas (https://github.com/jfarseneau/antennas/releases). This app translates the Tvheadend API to emulate a HDHomeRun API. When I try to use this app with nextPVR plex can see the tuner but needs to scan for channels which fails. I have attached pictures of this.
Is It possible to get this working with nextPVR? I dont like TvHeadEnd and would rather use nextPVR If possible.
I am using NPVR on a Windows 10 desktop, with the Hauppauge WinTVDual tuners. I record over-the-air broadcasts, and recently upgraded my antenna. When I click the "live" version of some channels, it works. But if I make a recording, it doesn't actually record, it just creates a .ts file in the folder with 0 bytes. I'm seeing the error "No errors, but no data delivered. This is usually because the device failed to lock a signal".
I also had two channels that would record the wrong variation of the channel (as in 24.2 rather than 24.1). I have scanned for channels again and manually deleted some, so I may have solved it, but I can't reproduce at the moment.
I bought a SAT>IP tuner several years ago but NextPVR & EPG Collector both don’t work with it on my server. It was not important as I had a twin DVB-S2 and twin DVB-T2 tuners and use the SAT>IP tuner for live TV with TVheadend! However one of the DVB-S2 tuners failed recently so investigated the SAT>IP tuner on a clean install of Windows 10 on another PC and the tuner worked as it should with both NextPVR and EPG Collector. The SAT>IP tuner still worked when the disk was put in the server with the DVB-S2 tuner in place and drivers installed. So back to testing with the disk on the separate PC with no connected tuners so not to interfere with daily recordings. I edit UpdateEPG.bat to remove the DVB-T2 related entries just leaving the very basic DVB-S2 related entries. If I run UpdateEPG.bat in a command prompt or double click in file manager it runs as expected and creates the xml EPG file!. However if I login to web admin and click "Update EPG" it stops almost immediately with "No tuners detected" error! Under Devices on Web Admin 4 SAT>IP are listed and not disabled! Enclosed is the log file.
I run updateEPG.bat 16:27:00 Finishes 16:30:04 success! Xml file saved to directory C:\EPG Log onto web admin and click Update EPG 16:35:00 16:35:01.017 “No tuners detected” This is now the only data in the file “UpdateEPG.bat” which has worked with the original tuners in the server for many years! "C:\Program Files (x86)\Geekzone\EPG Collector\EPGCollector.exe" /ini="C:\EPG\EPG Collector Freesat.ini"
Chris
Recently upgraded to latest NextPVR for Windows and a program with an ampersand (&) in the name consistently gets "locked" and cannot be deleted without restarting the NextPVR Service. Possibly similar to another issue I saw reported, but nothing about an ampersand there that I saw. Issue starts at 11:00:00.105 in attached log.
Hello,
I am using a IT9135BDA DVB-T USB TV Tuner on my windows 11 machine. When trying to scan channels on NextPVR It instantly says "Scanning: 683500KHz (7MHz b/w) (0 channels found)". I am able to use this tv tuner fine with some other programs.
When looking in the logs I noticed the following errors
FindFilterByName failed to locate filter: MainConcept (HCW) MPEG Multiplexer-Plus
MainConcept mux not present. Disabling analog support.
Is this an issue with my tv tuner or something else?
