Device Channels for Australia Missing

[flywire]

I want to install Mt-Ulandra: http://ozdigitaltv.com/transmitters/NSW/96-Mt-Ulandra

Callsign Frequency Power (ERP)
ABC46 655.500 Mhz 350.00 kW
CBN47 662.500 Mhz 350.00 kW
SBS48 669.500 Mhz 350.00 kW
WIN50 683.500 Mhz 350.00 kW
CTC51 690.500 Mhz 350.00 kW


Device: Hauppauge WinTV 88x DVB-T Tuner/Demod
Enabled

Common Interface H/W
Australia
SW Slopes-E Riverina
Scan Offsets

Digital Channel Setup displays Scanning: 655500KHz (7MHz b/w.) and Scan only loads the ABC46 655.500 Mhz Channels.

How do I load the other channels?

I have no other tuner devices.

[Graham]

How do I load the other channels?

The DVB-T folder within the Tuning folder within the NextPVR data folder holds a single .ini file for each transmitter. The file for your transmitter is probably out of date. You should be able to find and update the .ini file.

Alternatively, a scan for All countries, All Regions should scan every frequency known to DVB-T and get you what you want ... though a full scan takes a bit longer.

http://www.nextpvr.com/nwiki/pmwiki.php?...alledParts

[flywire]

... The file for your transmitter is probably out of date. ...[/url]

I think it must be something else. The ini file looks fine to me comparing it to list in 1st post:

>>>> File: Australia - SW Slopes-E Riverina.ini

[TERTYPE]
1=Australia
2=SW Slopes-E Riverina

[DVB]
0=5
1=1,655500,0,0,7
2=2,662500,0,0,7
3=3,669500,0,0,7
4=4,683500,0,0,7
5=5,690500,0,0,7

[martint123]

Run a scan and upload your log files so the knowledgeable can see what is (or not) happening.

[flywire]

... upload your log files ...

Refer post #3.

[martint123]

Refer post #3.

Sneaked in after

I'm no expert, but it looks wrong - 4 scans of the same frequency 655500.

This doesn't look too healthy. (but I don't know enough to say why!)

2015-01-05 23:50:14.812 [DEBUG][5] FindFilterByName failed to locate filter: WinTVCIUSBBDA Source

[sub]

flywire, set CI / CAM back to 'None'. You've got it set to 'Common Interface H/W'.

[flywire]

... set CI / CAM back to 'None'. ...

Yes, after three tries that has done it.

Now :confused: programs appear in TV guide but show detail, watch does not yet work. Just please wait and then to blank screen. I suppose this is a decoders issue.

[Zeb]

Live TV buffer is in a user's folder. Recording service runs as System, so you should put the buffer in Users/Public or C:/Temp unless you're well acquainted with permissions. You also need to select an MPEG2 Video decoder on the Settings/Decoders screen (I seem to recall that H.264 isn't used in Australia). If that's Windows 7 you can select Microsoft's decoder. If Hauppauge WinTV is installed, you should have a MainConcept decoder. If your PC lacks a suitable decoder, maybe install forum member Hoborg's SAF decoder pack (send him a PM requesting "unlocked" version if you go that route). Brrr, it's a cold morning in U.S.A.

[flywire]

Thanks for the support.

Ok, that seems to have viewing working on Win 7. A Manual record of a TV show worked.

I don't understand why the default Media folders are all C:\