What settings to tweak to get more channels

***sub*** · 2008-09-22, 04:45 AM

Did it find your channels on that scan attempt? if so, did they have valid names, or "unknown" names?

jman11 · 2008-09-22, 05:49 AM

It found quite a few channels, but almost all had "unknown" names.

***sub*** · 2008-09-22, 05:53 AM

For me to check why its not scanning you might need to try setting your mux to 'full ts', then do a 1 minute recording of one of those unknown channels, then make the resulting ts file available to me.

observer_11 · 2008-09-22, 09:47 PM

jman11 Wrote:It found quite a few channels, but almost all had "unknown" names.

The "unknown" is most likely caused by your <BDAPsiScanStartupSeconds> and
<BDAPsiScanWaitSeconds> settings.

jman11 · 2008-09-22, 11:24 PM

observer11, what settings do you use? default?

observer_11 · 2008-09-22, 11:56 PM

jman11 Wrote:observer11, what settings do you use? default?

I'm currently using 2 and 20 with BDATwinhanDiseqcMethod = 0. I am not sure what the default settings were - wish I knew since I forgot to back it up. Maybe 5 and 25? I have an old config.xml in which I was using 1 and 10 and BDATwinhanDiseqcMethod = 2 - don't remember how well that worked... :o

***sub*** · 2008-09-22, 11:58 PM

config-master.dont-edit-me.xml has the defaults.

jman11 · 2008-10-05, 10:44 PM

Sorry for dropping this thread - I was out of town for a week.

I did a manual work around and went into the scan-* files and manually added the channel names.

Question: what does epg key off of - channel name, channel number, a combination of info?

bundys · 2009-03-16, 06:24 PM

jman11 Wrote:Sorry for dropping this thread - I was out of town for a week.

I did a manual work around and went into the scan-* files and manually added the channel names.

Question: what does epg key off of - channel name, channel number, a combination of info?

Would like to know about the epg as well. Have gbpvr set to use the stream for dish epg, but have not been able to get a single entry to show up in the epg.

***sub*** · 2009-03-16, 06:28 PM

bundys Wrote:Would like to know about the epg as well. Have gbpvr set to use the stream for dish epg, but have not been able to get a single entry to show up in the epg.

If you've been trying the DVB EPG, then you probably need to switch the Schedules Direct or some XMLTV source. Dish Network is not using the standard DVB EPG.

Possibly Related Threads…
Thread		Author	Replies	Views	Last Post
	no EPG for two channels	JimPletcher	5	4,871	2019-08-15, 09:53 PM Last Post: jobby99
	Locking in QAM Channels	highestbid	8	7,567	2014-03-12, 03:10 AM Last Post: highestbid
	Need help remapping Channel guide and actual channels	divinehammer	3	3,852	2012-01-20, 10:43 AM Last Post: kayleigh
	Two Channels Without Video	skycyclepilot	5	3,600	2011-10-29, 07:49 PM Last Post: sub
	No sound for French DVB-T H264 channels with E-AC3 tracks	jorionpi	7	4,798	2011-06-26, 01:25 AM Last Post: sub
	Problem with GB-PVR - Cannot Watch Channels and Administrator Problem	Greg Smith	10	4,619	2011-05-22, 05:09 PM Last Post: sub
	no channels found - XP x64 bit edition fresh install	8ace	3	2,022	2011-02-10, 01:27 AM Last Post: 8ace
	Missing Channels In Listings?	hollow5555	4	2,430	2011-01-10, 05:53 PM Last Post: hollow5555
	No QAM channels being retrieved with HVR-2250	Misko5	4	2,456	2011-01-01, 01:45 AM Last Post: Snooze
	mc2xml Digital Channels	235301	8	5,507	2010-12-30, 05:12 PM Last Post: joseosoria