As I'm now finally up and running with my DVB card, I now have to work through some more issues.
Remote behavior (logs attched):
Start PVRX2 with green button, remote works fine in all menus etc. Start Live TV and remote stops working, use mouse to exit Live TV. Remote works again in Menu screens etc, start Live TV again and remote works!
This I have tested many times. I have to go in and out of live TV to get the remote to work in Live TV. Looks like the remote bit gets shut out the first time the DVB card is connecting to a channel. (remember I'm running mutidec+card reader)
Recording: If I have 2 recordings in succession, the second recording will not work. It makes a file of the right size, just wont play it after the recording is finished. If one watches it while recording, it plays. I have checked both shows in WMP, the first plays, the second will not play. Wife not happy!
I also notices that if I watch a recording whike it is stil recording, the timeline at the tops show som strange behavior, the recoding time goes way too fast and a 45 min show shows about 2 hours! Like it is in a time warp!
Also, if one exits the above, and goes back in, resume does not go to the spot form were one exited. It goes to and ealier point!
I have not set conversion to anything yet and have the BDA multiplexer set to MS DVR-MS. I have read the sticky mux thead but are non the wiser. I will have to try some of the stuff as I have sync issues.
Config:
I would like to set the low signal popup delay in config to more the 5 secs. However after re-installing GBPVR, if I change the value and save GBPVR will not work and I have to revert to my backed up config.xml. All I'm doing is opening config.xml in notepad, changing the value from 5 to 8, saving, and exiting. It worked before! It's like its making the config file unreadable to GBPVR.
Remote behavior (logs attched):
Start PVRX2 with green button, remote works fine in all menus etc. Start Live TV and remote stops working, use mouse to exit Live TV. Remote works again in Menu screens etc, start Live TV again and remote works!
This I have tested many times. I have to go in and out of live TV to get the remote to work in Live TV. Looks like the remote bit gets shut out the first time the DVB card is connecting to a channel. (remember I'm running mutidec+card reader)
Recording: If I have 2 recordings in succession, the second recording will not work. It makes a file of the right size, just wont play it after the recording is finished. If one watches it while recording, it plays. I have checked both shows in WMP, the first plays, the second will not play. Wife not happy!
I also notices that if I watch a recording whike it is stil recording, the timeline at the tops show som strange behavior, the recoding time goes way too fast and a 45 min show shows about 2 hours! Like it is in a time warp!
Also, if one exits the above, and goes back in, resume does not go to the spot form were one exited. It goes to and ealier point!
I have not set conversion to anything yet and have the BDA multiplexer set to MS DVR-MS. I have read the sticky mux thead but are non the wiser. I will have to try some of the stuff as I have sync issues.
Config:
I would like to set the low signal popup delay in config to more the 5 secs. However after re-installing GBPVR, if I change the value and save GBPVR will not work and I have to revert to my backed up config.xml. All I'm doing is opening config.xml in notepad, changing the value from 5 to 8, saving, and exiting. It worked before! It's like its making the config file unreadable to GBPVR.
[COLOR="Silver"][SIZE="1"] NPVR Latest version on W7 Home prem, SAF 5, TT-1500 DVB-S with CI, conax cam, USBURIT, LM Remote, Hauppauge 45 remote, Abit K9, Athlon 64 X2 3600 with Zalman CNPS8700 fan, 2G Ram, HIS Radeon HD 5570 1GB, 60GB Corsair SSD sys disk, 500GB sata recording, 1TB Media, Siversotone LC17, TV: KDL40NX700AEP[/SIZE][/COLOR]