Automated Cutting and Transcoding Guide Using Mencoder

[superflysocal]

Not 100% sure (stattik should verify), but I think you need to add the following after the :cleanup label in the batch file:

Code:

:cleanup IF /I %update_db% EQU yes ( ECHO. ECHO Updating GBPVR database with new extension--%output% ECHO. FOR %%d in (%output%) DO ( FOR %%b in (%name%) DO ( %sqlite3_path%sqlite3.exe -separator "," "%gbpvr_db_path%" "UPDATE RECORDING_SCHEDULE SET filename = '%local_recordings_disk_letter%%%~pnxd' where filename like '%local_recordings_disk_letter%%%~pnxb';" SET question_mark_check1=%local_recordings_disk_letter%%%~pnd SET question_mark_check2=%%~nxd SET question_mark_check3=%local_recordings_disk_letter%%%~pnb SET question_mark_check4=%%~nxb ) ) ) [B][SIZE=3][COLOR=red]IF /I %dvdrip% NEQ yes ([/COLOR][/SIZE][/B] [B][SIZE=3][COLOR=red]WizRenameRecording "%newname%" -default[/COLOR][/SIZE][/B] [B][SIZE=3][COLOR=red])[/COLOR][/SIZE][/B] %debug%

This implies that you've run WizRename recording and set a default pattern.

so would i still need to post the snipet that I posted above (which I got from you) or does this replace that? if so, where does that goes?

[JavaWiz]

so would i still need to post the snipet that I posted above (which I got from you) or does this replace that? if so, where does that goes?

The original snippet was more for a stand-alone batch file, or what could be used in PostProcessing.bat which is triggered after the recording is complete. Depending on how you trigger stattik's script, you may just want to rename the recording in PostProcesisng.bat, then when you trigger stattik's script, the file will already be renamed.

If you still want the rename in stattik's batch file, you only need to find the appropriate place to call WizRenameRecording.exe, and the correct variable name to use. I'm not familiar with that batch file, but it looks like either %output% or %newname% are the possible variables. I think this call needs to be added somewhere near the end of the processing, but not 100% sure where it makes most sense to place it.

As I've looked at it more, I suspect it may be best to put the following lines right after the :del_files call at the bottom of the script:

Code:

:: IF CLEANUP IS ENABLED, EDL FILES ARE DELETED ONCE THE ASSOCIATED VIDEO IS DELETED FOR /R %recordings_path% %%t IN (*.edl) DO ( CALL :del_edlfiles "%%t" ) :: Call WizRenameRecording for all NON DVD Rip files IF /I %dvdrip% NEQ yes ( WizRenameRecording "%newname%" -default ) :: #### Script is finished #### ECHO. ECHO Script is finished. ECHO.

I've limited the rename to only those that are not DVD rips, not sure that the rename makes sense for those...

[superflysocal]

The original snippet was more for a stand-alone batch file, or what could be used in PostProcessing.bat which is triggered after the recording is complete. Depending on how you trigger stattik's script, you may just want to rename the recording in PostProcesisng.bat, then when you trigger stattik's script, the file will already be renamed.

If you still want the rename in stattik's batch file, you only need to find the appropriate place to call WizRenameRecording.exe, and the correct variable name to use. I'm not familiar with that batch file, but it looks like either %output% or %newname% are the possible variables. I think this call needs to be added somewhere near the end of the processing, but not 100% sure where it makes most sense to place it.

As I've looked at it more, I suspect it may be best to put the following lines right after the :del_files call at the bottom of the script:

Code:

:: IF CLEANUP IS ENABLED, EDL FILES ARE DELETED ONCE THE ASSOCIATED VIDEO IS DELETED FOR /R %recordings_path% %%t IN (*.edl) DO ( CALL :del_edlfiles "%%t" ) :: Call WizRenameRecording for all NON DVD Rip files IF /I %dvdrip% NEQ yes ( WizRenameRecording "%newname%" -default ) :: #### Script is finished #### ECHO. ECHO Script is finished. ECHO.

I've limited the rename to only those that are not DVD rips, not sure that the rename makes sense for those...

Actually, stattik's script is my Postprocessing.bat right now. That's why i think Wizrecordrename should be done before stattik's script as you mentioned above. That way, it will let stattik's script take care of updating the databse also. I wanted to put your Wizrenamerecording snipet that i posted earlier in the Postprocessing.bat (which is stattik's script) but before the start of his "main code". Your snipet would output a %newname% variable. i just don't know how to change this part of his main code to use that new variable instead of %1.

PHP Code:

::      BEGIN MAIN SCRIPT 
SET name=%1 
SET short_name="%~nx1" 
SET title="%~n1" 
SET source_size=%~z1 
SET start_opt="%short_name:"=% - stattik_transcode" /low /wait /min 


I figure i can do SET name=%newname% but I don't know how to change short_name and title.

[-stattik-]

i am using 0.5.1f (from the wiki) and it's not there. I do see it in 0.5.6ar but should I use 0.5.6br instead and which version (I see it posted a few times).

0.5.6br would be the most up-to-date version. I haven't posted it to the WIKI because there's a few things I need to add first.

Also, what should I set the move_dir to if I don't want the file moved?

Code:

SET cleanup=no

That will turn off moving.

[-stattik-]

If I am running comskip here in your script (as PostProcessing.bat with comskip=yes) should I set commercial detection to None in GBPVR config program?

Yes

:: BEGIN MAIN SCRIPT
SET name=%1
SET short_name="%~nx1"
SET title="%~n1"
SET source_size=%~z1
SET start_opt="%short_name:"=% - stattik_transcode" /low /wait /min

%output% is going the be the final name.

so what i want is:
originalname.mpg to newfilename.mpg (wizardrename)
newfilename.mpg converted to newfilename.avi (stattik's script)
library point to newfilename.avi (stattik's script)

or
originalname.mpg to originalname.avi (stattik's script)
originalname.avi to newfilename.avi (wizardrename)
library point to newfilename.avi (stattik's script)

The second version would more plausible. I'm not sure what will change with the rename but the current version of the script searches the GBPVR DB using the original name. If the name is changed, it most likely won't find it. Can you give me an example of how the would look like after the rename?

[-stattik-]

Not 100% sure (stattik should verify), but I think you need to add the following after the :cleanup label in the batch file:

Code:

:cleanup IF /I %update_db% EQU yes ( ECHO. ECHO Updating GBPVR database with new extension--%output% ECHO. FOR %%d in (%output%) DO ( FOR %%b in (%name%) DO ( %sqlite3_path%sqlite3.exe -separator "," "%gbpvr_db_path%" "UPDATE RECORDING_SCHEDULE SET filename = '%local_recordings_disk_letter%%%~pnxd' where filename like '%local_recordings_disk_letter%%%~pnxb';" SET question_mark_check1=%local_recordings_disk_letter%%%~pnd SET question_mark_check2=%%~nxd SET question_mark_check3=%local_recordings_disk_letter%%%~pnb SET question_mark_check4=%%~nxb ) ) ) [B][SIZE=3][COLOR=red]IF /I %dvdrip% NEQ yes ([/COLOR][/SIZE][/B] [B][SIZE=3][COLOR=red]WizRenameRecording "%newname%" -default[/COLOR][/SIZE][/B] [B][SIZE=3][COLOR=red])[/COLOR][/SIZE][/B] %debug%

This implies that you've run WizRename recording and set a default pattern.

That placing is fine. This would be the addition:

Code:

IF /I %dvdrip% NEQ yes ( WizRenameRecording "%output%" -default )

There still is the matter of updating the DB with the new name.

[JavaWiz]

This is what I think you can do.

1) Rename stattik's script back to stattik_transcode_0.5.1f.bat
2) Place the renamed file in gbpvr root directory.
3) Use the new PostProcessing.bat. (see attached file)

This will call WizRenameRecording to rename the file and update the db with the new name. The stattik transcode script does not have to be changed at all.

As well as outputting to the screen, it will create a logs/PostProcessing.log file.

[-stattik-]

That looks like a good solution JavaWiz. Only WizRenameRecording knows the current and new names so it would be best to update the DB from there.

[superflysocal]

This is what I think you can do.

1) Rename stattik's script back to stattik_transcode_0.5.1f.bat
2) Place the renamed file in gbpvr root directory.
3) Use the new PostProcessing.bat. (see attached file)

This will call WizRenameRecording to rename the file and update the db with the new name. The stattik transcode script does not have to be changed at all.

As well as outputting to the screen, it will create a logs/PostProcessing.log file.

Thanks for both your help, Wiz and stattik. I am using 0.5.6br.bat so i changed that in your Postprocessing.bat as well as the WizRename options to {show}{[-]}{episode}-{month}{day}{yearShort}-{hour}{minute}. I will try it now and report back. I'm surprise I am the first to ask of this to combine two such wonderful scripts/apps.

[superflysocal]

It appears to working! Thanks again to both of you for the help and support.

Now i just need to tweak comskip. With this new arrangement, it appears that comskip might somehow be running twice because the .avi file is starting a lot later than the start of the show.