Cinergy T2 BDA

[fishy6969]

I've just got one of the freeview digital doda's from Terratec - the Cinergy t2. Have finally got it working with GBPVR.

The BDA drivers are here : http://supportde.terratec.net/modules.ph...it&lid=790

And this seems to work in the bda.ini file :

[CinergyT2 USB]
TUNING_TYPE=DVB-T
RECEIVER_ONLY_MODE=1
FILTER_RECEIVER=Cinergy T2 Tuner/Demodulator
PIN_RECEIVER_IN=Antenna In Pin
PIN_RECEIVER_OUT=MPEG2 Transport

Hope this is useful!

[sub]

Cheers. I'll add this to the master file.

[loffe]

I know the card is based on the same chip as Nova-T so I tried:

[TerraTec Cinergy 1200 DVB-T]
TUNING_TYPE=DVB-T
FILTER_TUNER=Cinergy 1200 DVB-T Tuner (BDA)
FILTER_CAPTURE=Cinergy 1200 DVB-T Capture (BDA)
PIN_TUNER_IN=Input0
PIN_TUNER_OUT=MPEG2 Transport
PIN_CAPTURE_IN=MPEG2 Transport
PIN_CAPTURE_OUT=MPEG2 Transport

It resulted in crash.

In the driver help the definition for mediaportal is:

<capturecard commercialname="TerraTec Cinergy 1200 DVB-T" capturename="Cinergy 1200 DVB-T Capture (BDA)" devid="ven_1131&amp;dev_7146&amp;subsys_1157153b&amp;rev_01">
<capabilities tv="true" radio="false" mpeg2="true" mce="false" sw="false" bda="true"></capabilities>
<tv>
<interface cat="capture" video="2" audio="3" mpeg2="1" sectionsandtables="5"></interface>
<filters>
<filter cat="networkprovider" name="Microsoft DVBT Network Provider" checkdevice="false"></filter>
<filter cat="tunerdevice" name="Cinergy 1200 DVB-T Tuner (BDA)" checkdevice="true"></filter>
<filter cat="capture" name="Cinergy 1200 DVB-T Capture (BDA)" checkdevice="true"></filter>
</filters>
<connections>
<connection sourcefilter="networkprovider" sourcepin="0" sinkfilter="tunerdevice" sinkpin="0"></connection>
<connection sourcefilter="tunerdevice" sourcepin="0" sinkfilter="capture" sinkpin="0"></connection>
</connections>
</tv>
</capturecard>

For the Nova T it's:

<capturecard commercialname="Hauppage Nova-T (Philips1)" capturename="TechnoTrend BDA/DVB Capture" devid="ven_1131&amp;dev_7146&amp;subsys_101113c2&amp;rev_01">
<capabilities tv="true" radio="false" mpeg2="true" mce="false" sw="false" bda="true"></capabilities>
<tv>
<interface cat="capture" video="2" audio="3" mpeg2="1" sectionsandtables="5"></interface>
<filters>
<filter cat="networkprovider" name="Microsoft DVBT Network Provider" checkdevice="false"></filter>
<filter cat="tunerdevice" name="TechnoTrend BDA/DVB-T Tuner" checkdevice="true"></filter>
<filter cat="capture" name="TechnoTrend BDA/DVB Capture" checkdevice="true"></filter>
</filters>
<connections>
<connection sourcefilter="networkprovider" sourcepin="0" sinkfilter="tunerdevice" sinkpin="0"></connection>
<connection sourcefilter="tunerdevice" sourcepin="0" sinkfilter="capture" sinkpin="0"></connection>
</connections>
</tv>
</capturecard>

And for the Cinergy T2:

<capturecard commercialname="TerraTec Cinergy T2" capturename="Cinergy T2 Tuner/Demodulator" devid="vid_0ccd&amp;pid_0038">
<capabilities tv="true" radio="false" mpeg2="true" mce="false" sw="false" bda="true"></capabilities>
<tv>
<interface cat="tunerdevice" video="2" audio="3" mpeg2="1" sectionsandtables="5"></interface>
<filters>
<filter cat="networkprovider" name="Microsoft DVBT Network Provider" checkdevice="false"></filter>
<filter cat="tunerdevice" name="Cinergy T2 Tuner/Demodulator" checkdevice="true"></filter>
</filters>
<connections>
<connection sourcefilter="networkprovider" sourcepin="0" sinkfilter="tunerdevice" sinkpin="0"></connection>
</connections>
</tv>
</capturecard>

So, any tip howto make it work? Would be very happy for help.

[sub]

All I can suggest is that you check the correct filter and pin names in GraphEdit, if it doesnt work when you've got the correct names, then you're out of luck.

[loffe]

I had entered the wrong device number. (I assumed that my analog devices where device 1 and 2)

[TerraTec Cinergy 1200 DVB-T]
TUNING_TYPE=DVB-T
FILTER_TUNER=Cinergy 1200 DVB-T Tuner (BDA)
FILTER_CAPTURE=Cinergy 1200 DVB-T Capture (BDA)
PIN_TUNER_IN=Input0
PIN_TUNER_OUT=MPEG2 Transport
PIN_CAPTURE_IN=MPEG2 Transport
PIN_CAPTURE_OUT=MPEG2 Transport


I still have problems with the swedish channels from SVT. It won't find them in the autosearch. I suspect an error when reaching the channel name "Kunsk/Barnkanalen" with the / in it. I think the problem is in the drivers and have contacted terratec.