HDHomeRun Dual problem

[sub]

Yep, looks like your BDA drivers are in a non-functional state. You probably need to uninstall the HDHR software, then reinstall, or something similar.

[locanda]

I will try that & report if & when successful.

[locanda]

Not successful. Uninstalled the Silicon Disk drivers. Ran the install again. NextPVR recording service status window still shows only IPTV. In the NextPVR application itself, in Settings, the Status also only shows IPTV. However, in the Settings>Devices panel, it does show the 4 ATSC devices as present and enabled (plus 4 QAM devices present & disabled), and allows Device Setup of same. Sees the device & IDs it correctly. Doing a Frequency scan now, and....is finding stations and their station ID. OK, found a bunch of stations (more than I had previously), so it seems to be accessing the device. Except for showing status & cannot use Live TV. Doing a short recording test...OK, this is interesting. Recording worked no problem.

So here is where I stand:

1. NextPVR does not report Status, either in the taskbar app or the full NextPVR program (under Settings).
2. I cannot access Live TV feature. It reports "Unable to find available capture device". Unfortunately, not having Live TV makes it impossible to be sure antenna stations are tuned in well.

Other than those 2 useful things, it works.

Do you have any suggestions for fixing those features?

[sub]

Try watching live tv, then post the logs and I'll look.

[locanda]

Try watching live tv, then post the logs and I'll look.

Here are the logs

[mvallevand]

Here are the logs

Which tuner is KLCS attached to?

Martin

[sub]

2018-06-04 12:42:41.242 [DEBUG][23] StartStream(7412:15 KLCS-1)
2018-06-04 12:42:41.242 [DEBUG][23] looking for capture source (in reverse priority order)
2018-06-04 12:42:41.242 [DEBUG][23] checking: Silicondust HDHomeRun Tuner 103C3C64-1 (ATSC)
2018-06-04 12:42:41.242 [DEBUG][23] checking: Silicondust HDHomeRun Tuner 103C3C64-0 (ATSC)
2018-06-04 12:42:41.242 [DEBUG][23] checking: Silicondust HDHomeRun Tuner 10325177-1 (ATSC)
2018-06-04 12:42:41.242 [DEBUG][23] checking: Silicondust HDHomeRun Tuner 10325177-0 (ATSC)
2018-06-04 12:42:41.242 [DEBUG][23] checking: IPTV Device
2018-06-04 12:42:41.242 [DEBUG][23] enabled and present
2018-06-04 12:42:41.242 [DEBUG][23] does not have channel
2018-06-04 12:42:41.242 [DEBUG][23] checking: Silicondust HDHomeRun Tuner 103C3C64-1 (QAM)
2018-06-04 12:42:41.242 [DEBUG][23] checking: Silicondust HDHomeRun Tuner 103C3C64-0 (QAM)
2018-06-04 12:42:41.242 [DEBUG][23] checking: Silicondust HDHomeRun Tuner 10325177-1 (QAM)
2018-06-04 12:42:41.242 [DEBUG][23] checking: Silicondust HDHomeRun Tuner 10325177-0 (QAM)
2018-06-04 12:48:41.444 [DEBUG][4] StartStream(7412:15 KLCS-1)
2018-06-04 12:48:41.444 [DEBUG][4] looking for capture source (in reverse priority order)
2018-06-04 12:48:41.444 [DEBUG][4] checking: Silicondust HDHomeRun Tuner 103C3C64-1 (ATSC)
2018-06-04 12:48:41.444 [DEBUG][4] checking: Silicondust HDHomeRun Tuner 103C3C64-0 (ATSC)
2018-06-04 12:48:41.444 [DEBUG][4] checking: Silicondust HDHomeRun Tuner 10325177-1 (ATSC)
2018-06-04 12:48:41.444 [DEBUG][4] checking: Silicondust HDHomeRun Tuner 10325177-0 (ATSC)
2018-06-04 12:48:41.444 [DEBUG][4] checking: IPTV Device
2018-06-04 12:48:41.444 [DEBUG][4] enabled and present
2018-06-04 12:48:41.444 [DEBUG][4] does not have channel
...etc...

How many of your capture devices have KLCS-1 setup? It looks like it's struggling to find a tuner with this channel.

For an experiment, it might be worth stopping the software, temporarily renaming your npvr.db3 to mybackup.db3, then starting the app again, so that it creates a new database, scan your channels, then see if you can watch your channels.

[locanda]

Which tuner is KLCS attached to?

Martin

All.

[locanda]

OK, have done as instructed and re-scanned. Live TV works and the devices are now also showing in the Status window. So, thanks, all fixed. Just have to re-map my channels to match my local TV Guide channel # listings. I seem to be hopeless at setting up the EPG, so do everything manually.

[sub]

Ok great.

I think somewhere along the way, installing update HDHR software or something, your device name changed slightly, so they looked like new devices. The old devices were still in your database, associated with your channels, but could no longer be found (since the names had changed). Setting it up again, the channels are associated with the correct channel names.