Hauppauge HVR1300 analog part, no success so far

[lif]

v0.9612

I've defined in config as PVR150 capture device #1 (also GBPVR config detects this card when tick show only detected cards). No problems with this one. Defined EPG source as XMLTV.

Defined second card (Hauppauge HVR1300 analog part) as source #1 and as Hauppauge Roslyn (GBPVR config card autodetection won't detect this card). When submitting OK it warns me about missing drivers(?!). EPG source left as none (as I already got EPG via PVR150 definition).

Channel list is the same for both cards.

When scheduling recording, it starts using PVR150. When going to LiveTV GBPVR warns me that no capture source is available and offers to cancel my request or to watch currently recording show (from PVR150). It does not start using Roslyn (or HVR1300 analogue).

From logs I find:

--- 8< ---
21:00:01.125 VERBOSE ConexantRecorder::StartRecording(2, 358, 191, 1)
21:00:01.578 VERBOSE target filename: \\192.168.0.102\d$\pvr\tv\Manual Recordings\TV3_20060321210000.mpg
21:00:02.156 VERBOSE Capture Device is based on BlackBird architecture
21:00:02.156 VERBOSE Capture Device is using Conexant (derived) drivers
21:00:02.156 VERBOSE Loading filter names
21:00:02.156 VERBOSE Found names:
21:00:02.156 VERBOSE Hauppauge WinTV 88x Crossbar
21:00:02.156 VERBOSE Hauppauge WinTV 88x Video Capture
21:00:02.156 VERBOSE Hauppauge WinTV 88x Tuner
21:00:02.156 VERBOSE Hauppauge WinTV 88x TvAudio
21:00:02.765 VERBOSE FindFilterByName failed to locate filter: Hauppauge WinTV 88x Crossbar
21:00:02.921 ERROR Failed to find Crossbar filter
21:00:03.031 VERBOSE ConexantRecorder::StopRecording()
--- >8 ---

Any comments? Suggestions? Solutions?

[sub]

Can you try running the attach utility, and post the resulting FilterCheck.log?

[lif]

FYI: My Hauppauge HVR-1300 model is HAU-1117 (if it makes any difference)

--- 8< ---

23:38:35.031 INFO Log started
23:38:35.031 INFO Filter Check v1.0
23:38:35.031 INFO
23:38:35.031 INFO
23:38:35.031 INFO Checking AM_KSCATEGORY_CAPTURE filters
23:38:35.125 INFO found: SoundMAX Digital Audio
23:38:35.203 INFO - (input) Volume
23:38:35.203 INFO - (output) Sum
23:38:35.203 INFO - (output) Recording Control
23:38:35.203 INFO - (input) ADC
23:38:35.203 INFO - (input) SPDIF Interface
23:38:35.203 INFO
23:38:35.218 INFO found: Hauppauge WinTV 88x Video Capture
23:38:35.281 INFO - (output) Capture
23:38:35.281 INFO - (output) Preview
23:38:35.281 INFO - (output) VBI
23:38:35.281 INFO - (input) Analog Video In
23:38:35.281 INFO - (output) 656
23:38:35.281 INFO - (output) I2S
23:38:35.281 INFO - (input) Analog Audio In
23:38:35.281 INFO
23:38:35.296 INFO found: Hauppauge WinTV 88x Audio Capture
23:38:35.296 INFO - (input) Audio Input
23:38:35.296 INFO - (output) Audio Capture
23:38:35.296 INFO
23:38:35.296 INFO found: Hauppauge WinTV PVR PCI II Capture
23:38:35.328 INFO - (input) Analog Video In
23:38:35.328 INFO - (input) Analog Audio In
23:38:35.328 INFO - (output) Capture
23:38:35.328 INFO - (output) Audio Out
23:38:35.328 INFO - (output) VBI
23:38:35.328 INFO - (output) 656
23:38:35.328 INFO
23:38:35.328 INFO
23:38:35.328 INFO
23:38:35.328 INFO Checking AM_KSCATEGORY_ENCODER filters
23:38:35.343 INFO found: Hauppauge WinTV 88x MPEG Encoder
23:38:35.359 INFO - (output) MPEG Out
23:38:35.359 INFO - (input) 656
23:38:35.359 INFO - (input) I2S
23:38:35.359 INFO
23:38:35.359 INFO found: Hauppauge WinTV 88x Audio Capture
23:38:35.359 INFO - (input) Audio Input
23:38:35.359 INFO - (output) Audio Capture
23:38:35.359 INFO
23:38:35.359 INFO found: Hauppauge WinTV PVR PCI II Encoder
23:38:35.359 INFO - (input) 656
23:38:35.359 INFO - (output) MPEG
23:38:35.359 INFO - (output) Mpeg Index
23:38:35.359 INFO
23:38:35.359 INFO
23:38:35.359 INFO
23:38:35.359 INFO Checking AM_KSCATEGORY_CROSSBAR filters
23:38:35.375 INFO found: Hauppauge WinTV PVR PCI II Crossbar
23:38:35.421 INFO - (input) 0: Video Tuner In
23:38:35.421 INFO - (input) 1: Audio Tuner In
23:38:35.421 INFO - (input) 2: Video SVideo In
23:38:35.421 INFO - (input) 3: Video Composite In
23:38:35.421 INFO - (input) 4: Audio Line In
23:38:35.421 INFO - (input) 5: Video SVideo In
23:38:35.421 INFO - (input) 6: Video Composite In
23:38:35.421 INFO - (input) 7: Audio Line In
23:38:35.421 INFO - (output) 0: Video Decoder Out
23:38:35.421 INFO - (output) 1: Audio Decoder Out
23:38:35.437 INFO
23:38:35.437 INFO found: Hauppauge WinTV 88x Crossbar
23:38:35.468 INFO - (input) 0: Video SVideo In
23:38:35.468 INFO - (input) 1: Video Tuner In
23:38:35.468 INFO - (input) 2: Video Composite In
23:38:35.468 INFO - (input) 3: Video SVideo In
23:38:35.468 INFO - (input) 4: Video Composite In
23:38:35.468 INFO - (input) 5: Video AUX In
23:38:35.468 INFO - (input) 6: Video ParallelDigital In
23:38:35.468 INFO - (input) 7: Audio Tuner In
23:38:35.468 INFO - (input) 8: Audio Line In
23:38:35.468 INFO - (input) 9: Audio Line In
23:38:35.468 INFO - (input) 10: Audio AUX In
23:38:35.468 INFO - (input) 11: Audio AUX In
23:38:35.468 INFO - (output) 0: Video Decoder Out
23:38:35.468 INFO - (output) 1: Audio Decoder Out
23:38:35.468 INFO
23:38:35.484 INFO
23:38:35.484 INFO
23:38:35.484 INFO Checking AM_KSCATEGORY_TVTUNER filters
23:38:35.484 INFO found: Hauppauge WinTV PVR PCI II TvTuner
23:38:35.515 INFO - (output) Analog Video
23:38:35.515 INFO - (output) Analog Audio
23:38:35.515 INFO
23:38:35.515 INFO found: Hauppauge WinTV 88x Tuner
23:38:35.531 INFO - (output) Analog Video
23:38:35.531 INFO - (output) Analog Audio
23:38:35.531 INFO
23:38:35.531 INFO
23:38:35.531 INFO
23:38:35.531 INFO Checking AM_KSCATEGORY_TVAUDIO filters
23:38:35.531 INFO found: Hauppauge WinTV 88x TvAudio
23:38:35.546 INFO - (input) TVAudio In
23:38:35.546 INFO - (output) TVAudio Out
23:38:35.546 INFO
23:38:35.546 INFO found: Hauppauge WinTV PVR PCI II TvAudio
23:38:35.546 INFO - (input) TVAudio In
23:38:35.546 INFO - (output) TVAudio Out
23:38:35.546 INFO
23:38:35.546 INFO
23:38:35.546 INFO
23:38:35.546 INFO Checking AM_KSCATEGORY_VBICODEC filters
23:38:35.546 INFO found: NABTS/FEC VBI Codec
23:38:35.609 INFO - (input) VBI
23:38:35.609 INFO - (output) NABTS
23:38:35.609 INFO - (input) HWNABTS
23:38:35.609 INFO
23:38:35.609 INFO found: CC Decoder
23:38:35.640 INFO - (input) VBI
23:38:35.640 INFO - (output) CC
23:38:35.640 INFO - (input) HWCC
23:38:35.640 INFO
23:38:35.640 INFO found: WST Codec
23:38:35.750 INFO - (input) VBI
23:38:35.750 INFO - (output) Teletext
23:38:35.750 INFO
23:38:35.750 INFO
23:38:35.750 INFO
23:38:35.750 INFO Checking KSCATEGORY_BDA_NETWORK_TUNER filters
23:38:35.781 INFO found: Hauppauge WinTV 88x DVB-T Tuner/Demod
23:38:35.843 INFO - (input) Input0
23:38:35.843 INFO - (output) MPEG2 Transport
23:38:35.843 INFO
23:38:35.843 INFO
23:38:35.843 INFO
23:38:35.843 INFO Checking KSCATEGORY_BDA_RECEIVER_COMPONENT filters
23:38:35.859 INFO found: Hauppauge WinTV 88x TS Capture
23:38:35.859 INFO - (input) MPEG2 Transport
23:38:35.859 INFO - (output) MPEG2 Transport
23:38:35.859 INFO
23:38:35.859 INFO found: BDA Slip De-Framer
23:38:35.968 INFO - (input) NABTS
23:38:35.968 INFO - (output) IPv4
23:38:35.968 INFO
23:38:35.984 INFO found: BDA MPE Filter
23:38:36.031 INFO - (input) MPE
23:38:36.031 INFO - (output) IPv4
23:38:36.031 INFO

--- >8 ---

[sub]

21:00:01.125 VERBOSE ConexantRecorder::StartRecording(2, 358, 191, 1)

Actually looking again are you original log snippet, I can see you've got the device number set wrong for the Hauppauge Roslyn. It should be set to device #1, you have it set to device #2.

[lif]

Sorry, the log I posted is few days old. I played with setting it as capture device 1 and 2 and 3 and actually didn't remember which log was which.

But issue is still active no matter which number it is. Also the same symtom is when I define Roslyn as my only capture device (remove PVR150). No ideas.

But, Sub, don't GBPVR config app should detect HVR1300 analog as Roslyn as when I tick checkbox called like 'Show only detected adapters'? It doesn't and shows only PVR150 then.

Actually looking again are you original log snippet, I can see you've got the device number set wrong for the Hauppauge Roslyn. It should be set to device #1, you have it set to device #2.

[sub]

Sorry, the log I posted is few days old. I played with setting it as capture device 1 and 2 and 3 and actually didn't remember which log was which.

But issue is still active no matter which number it is. Also the same symtom is when I define Roslyn as my only capture device (remove PVR150). No ideas.

Set the device number correct, then reproduce the problem, then zip and attach the logs and I'll take another look.

[lif]

I did GBPVR clean install and configured PVR150 and HVR1300 (analog) to same channels. Didn't work and GBPVR opened window as capture source not available etc. So, I decided to edit gbpvr.mdb manually to correct channel oid mappings. There was a complete mess as some channels were twice, some were once, some pointing to I don't know where it got these freq channel numbers etc. I cleared and defined manually there.

After that GBPVR was able to record with both tuners the same (or different) channel at the same time! But only to record! If I define manual (or via guide) rec on PVR150 and then trying to watch Live TV (it should then use the first available tuner). GBPVR crashes with Framework/C++ error! I didn't find any trace from log files (as the crash was immediate, before it logged anything). I could reproduce situation every time when PVR150 is busy and it tryes to use "Roslyn".

Also with recording it has one major problem - no sound! PVR150 recording was fine, but HVR1300 "Roslyn" recording had no sound! Picture was with right colors and quite good quality (not so good as PVR150, but still quite good).

So, what should I do? What utils/logs/mdb/etc. do you need? I consider myself as quite a professional in IT but can't understand why others could use HVR1300 as "Roslyn" without any problem and I haven't had any success. :confused:

[sub]

After that GBPVR was able to record with both tuners the same (or different) channel at the same time! But only to record! If I define manual (or via guide) rec on PVR150 and then trying to watch Live TV (it should then use the first available tuner). GBPVR crashes with Framework/C++ error! I didn't find any trace from log files (as the crash was immediate, before it logged anything). I could reproduce situation every time when PVR150 is busy and it tryes to use "Roslyn".

Reproduce the problem, then zip and attach a complete set of logs and I'll take a look.

[lif]

Did that. PVR150 is recording from "Kanal 2" and simultanously trying to watch "ETV" with "Roslyn" (HVR1300). All *.log *.ini and config.xml and gbpvr.mdb are included. Also the screenshot of the error in jpg. All logs are copied straight after the error occured. After pressing either button on error message, windows kills GBPVR process immediately.

[ATTACHMENT NOT FOUND]

"ummik" means in Estonian like traffic jam or deadlock...

[lif]

from "Roslyn" - Live TV crashes, recording only records video stream, no audio stream is included in resulting .mpg file.