I've got a remote that works fine on a system with a HVR-3000 but I can't seem to get it working on another system with a new install of GBPVR 1.2.9 and HVR-900.
I've confirmed that the irremote.ini settings for GBPVR are there but it doesn't seem to respond to any buttons at all. I've only installed ir32.exe. No WinTV or Powercinema.
I'd really appreciate if any using the HVR-900 with a remote can let me know if there is a trick to getting it going or some way to verify outside of GBPVR that the remote receiver is actually working.
Hey,
I've got a weird one. I've installed gbpvr on a computer with a dvb-s card, and a large library of multimedia files. I can play both live tv, and multimedia files with no problems on the gbpvr server itself fine. However I can view any video/audio on the pch other than the gbpvr menus. I installed according to the guide, and I think I have all the latest plugins for the hd gbpvr menus, etc as well as the latest mvpmc client for the pch. I can telnet, etc to the pch fine, and the gbpvr menus display fine, I can select through them with the remote, etc. However when I go to play either live tv, or a mm file it goes to a blank screen and then after 5-10 seconds shows the popcorn hour screen and comes back to the select source menu on the pch.
My pch is set to 1080i 60hz, I've set the mvpmc config line to all kinds of options and currently have it set with just the -o hdmi & option. Menus in the gbpvr screen look fine and dont bleed through, fall offscreen, etc. In my config.xml I have the following section..
<MAC-0006DCxxxxxx>
<MVPClientType>PCH</MVPClientType>
<MVPWidth>1280</MVPWidth>
<MVPHeight>720</MVPHeight>
<MVPOffsetX>0</MVPOffsetX>
<MVPOffsetY>0</MVPOffsetY>
<MVPSendIncrementalUpdates>true</MVPSendIncrementalUpdates>
</MAC-0006DCxxxxx>
This is the only weird error message I see in the application log.
Faulting application ffmpeg.exe, version 0.0.0.0, faulting module ffmpeg.exe, version 0.0.0.0, fault address 0x001d044b.
I have 9 channels that are three hours off. because Zap2it refuses to fix them. Is there a way to change channel times so that they are the right times?
I have NINE channels that are 3 hrs off the schedule. I want the ability to change the times of these channels to right times without messing with the other channels.
I am trying to use freq2xml and freq2reg to set up channel numbers and channel names. In my case, channel numbers (what is called the preset number in the presets.txt file) start from 36 and they are not contiguous. A small part of the listing is as follows:
The channel ids above are all dummy values. I have added the reg file to the registry and have verified that the frequencies start from 36 under HKLM->...->TS0-1 key. I have generated the xml file and chose USA and cable for the capture card.
But when I import the xml file, the source channel always start from 0 and increase sequentially. It seems that it is not looking under the TS0-1 key. Is ther a way I can find out which TSxx-1 key is it looking for? What am I doing wrong?
While I am at it, how can I add my country's country code to GBPVR? The name is Pakistan, the code is 92 and tv system is PAL-B.
I'm sure many of you have deployed MVP1000's to your children's rooms. What would be a great addition I think is to add a parental lock feature on things such as certain movie folders and especially certain TV channels.
Here in the US we have the V Chip which most (but not all including Cartoon Network) providers honour. It would be great if we could get that into the MVP setup some how.
Can we read the V Chip info within GBPVR? Could V Chip be a useful and socially responsible addition to GBPVR?
I'm sure that there are other V Chip type systems elsewhere on the planet.
I have used GBPVR before way back on a W2K box. My new mediacenter PC is XP MCE and I wanted to give GBPVR another shot, just to see what's changed and what's new.
I have been through the forums and seen a few people having this problem. I have tried downloading it 4 times, using two different browsers. I still cannot get past this error where it states that .cab is corrupt.
Is this cab even IN the installation? I even was going to download a previous version and try an upgrade, but I cannot find a working link for previous versions as well.
Is there a fix for the cab problem, or what about a .ZIP instead of the .MSI?
I thought I had successfully installed GB on my new Vista load, but when I went to add plugins, they don't show up in the plugin menu. Also, I get an error when starting up config, but I then get the config menu (minus the plugins).
HELP!
I get: Error loading plugin list Systemargumentout of rangeexception and it goes on to mention TVListings. However I think there's something wrong with the install and tvlistings is just the first plugin it tries to load.
I am recently facing a problem after setting up my new htpc:
My new htpc have a board with intel 3100 Grafik (G31 chipset) and my flat tv is connected via DVI->HDMI. Everything fine so far. I managed the resultion and refresh rate (which was not easy by the way)
but:
If I switch of the TV while the pc is running, maybe recording, the grafikdriver will close the dvi port. I can hear the windows signal of hardware removed (in this case the tv). But if I switch then the tv on there are another windows ping (pnp: tv is there) but the grafikdriver will not open the dvi again and therefore I get no picture. I have to shutdown or hibernate the pc and the picture will be restored after the next start.
After reading a lot of other boards I'v learned that it is a common problem with dvi hdmi connections and ati has solved this with its latest 8.3 drivern, nvidia seems too. But Intel ? I'm using the latest Intel drivers.
Anybody out there knows any solution? Maybe some older Intel driver versions ? Or any hidden betadriver anywhere ?
Or any programming guru here wich knows how to tell the Intel driver to do a "re-initialse" ? I could catch th windows "hardware has changend" message. Maybe filtering if it was the montior (tv) that was connected and then send a "reset" to the drivers" ?
I had the PVR2 EPG set to update from Freeview at 5am and it would not update automatically when I was away from my computer (which was always on with standby deactivated). I then set it to 6am and it still doesn't auto-update. I've tried it with the PRV2 application running and with PVR2 not running and it doesn't update either way and its been like this for weeks. The only way to update the EPG is to do it manually.