After trying to update EPG with the new version, I'm getting the following error that is attached.

Ok, everyone, I am having a major issue here. I've read some stuff on the board about this, but I'm not sure if I understand the problem and/or the solution correctly. Basically, in

order for the PVR-150 driver to work, I have to turn off hardware acceleration on ASUS's video card driver. If I have hardware acceleration turned on, GB-PVR will report some internal

error and then later report no capture devices present(WinTV2000 bombs too). Without hardware accerelation turned on, I can't get to the TV out functionality of the card. This card is

PCI-E BTW. I called hauppauge and they said this can occur and is caused by the video card's hardware acceleration taking up too much bandwidth. People have been talking on the board

about the VMR modes, but I am using Overlay because the GB-PVR documentation said that overlay was my only choice for Win2k(Why?, Is this really true?). Also, I vauguely remember seeing

some driver/utility for the MB that I don't think I loaded for, besides for other things(Raid?), helping the NForce chipset direct PCI-E signals optimallty. Is something like this

required.

I'm not sure what direction to turn here. What should I try next? Has anybody else resovled this issue? Should I just look for an ATI9550(Non-ASUS) card?

I am having a problem with the USBUIRT I have setup to change channels on my set top box. It seems that the #2 wants to repeat itself, so when I change to channel 22 it sends 222 to the set top box. Or when I change to 132 it sends 1322, changing the channel to 322 on the set top box. The weird thing is that if I load GBPVR, then go to live TV the speed at which the USBUIRT flashes to change the channel has a longer delay than if I change the channel once Live TV is showing.

For example, I start Live TV and it changes to channel 132. The USBUIRT flashes three times with a noticible pause in between. The set top box changes to 132 as expected. I change to channel 22 by pressing 22 on the remote, the flashes from the USBUIRT have very little if any delay, and the channel changes to 222.

So now the million dollar question... is there a setting in GBPVR for the delay between transmission of each channel sent from the USBUIRT?

I would like to burn recordings from gbpvr to DVD and am running into a problem (not related to gbpvr). I am using the ULEAD movie creator (?) that came with my Hauppauge 150 card (I have also tried Nero). If I try to burn a show that was 2 hours, it says there is not enough capacity on a DVD. It does not matter the size of the mpg file (based on recording in high or medium quality). It also does not matter what quality level I use for the burning. Any suggestions on how to do this would be greatly appreciated.

Taz

If I enter timeshift mode during Live TV, and try to play the recording, the screen turns green completely after about 3 seconds of playing video in that mode.

This problem only seems to afflict timeshift mode, because if I manually record something, the problem doesn't seem to exist. Any ideas, or are more specifics needed?

OK - let me slip back into dumb mode here.

I've just re-built my PC and it's now running MCE but so far I've been unable to play anything back (that needs transcoding) on the MVP...

00:27:21.368 INFO Log started
00:27:21.384 INFO TRANSCODING: C:\temp\CHAMPI~1.DVR
00:27:21.384 INFO TARGET: D:\Recorded TV\MVP000DFE0067CB.mpg
00:27:21.384 INFO ...
00:27:21.446 INFO T1
00:27:22.555 INFO T2.
00:27:22.555 INFO T5
00:27:22.555 INFO T6
00:27:22.555 VERBOSE DVR-MS file type.
00:27:23.305 ERROR fileSourceFilter->Load() failed: 80070005
00:27:23.774 VERBOSE Using Hauppauge WinTV MPEG2 Muxer
00:27:23.805 VERBOSE About to list graph filters
00:27:23.805 INFO Graph contains the following filters:
00:27:23.805 INFO - Hauppauge WinTV MPEG2 Muxer
00:27:23.805 INFO - D:\Recorded TV\MVP000DFE0067CB.mpg
00:27:23.805 INFO - C:\temp\CHAMPI~1.DVR
00:27:24.087 VERBOSE About to start graph

Now I know I've missed something fundamental here but bear with me, I'm not as young as I once was.... and a lot older than before I was married!!

I read this as the DVR file not existing/being readable but it does get created.

Thanks,
C.

I have been trying to setup my DVICO Fusion HDTV Gold tuner and have been have a lot of trouble. I have been able to find channels with Zap2It. I am just trying to get the normal non-HD cable stations, not the QAM, so that is not my problem. See the images below for my problems. Any help would be greatly appreciated!!

I was having an occasional problem playing recordings from VA 3.0, so I uninstalled both VA and GB-PVR 97.7 and reinstalled them. Now I do not see any recordings in the VA Recordings list, though they show up properly in the GB-PVR Video Library. But in VA Recordings, all I see is a blank page and the moving hour glass, which I have let run for 15 minutes with no success. This must be a simple configuration error, but I don't see it.

Hi Sub,

sometimes when I listen to music using My Music, the inset does not stop even though all music has stopped - I've pressed stop. All that's left is a black inset and it covers up half my screen and all my panels. Even when I enter a plugin, the inset is still there.

I have to restart GBPVR to get rid of it.

It wouldn't matter to me because I would prefer to have inset off, but for some weird reason my wife likes it.

I use the ContourHC skin and use My Music to play tracks.

I am also still using the latest 96.XXX release.

Thanks

Could this method be made to work even when GBPVR is not running. Or, if not, is there another way for me create the DbProviderFactory factory object myself?

Thanks

Jeff