I've noticed a couple of things when I am watching a show that I am recording. (set up to record, start watching say 15 minutes later)

If you pause the screen, you get the show length, but that never updates, so if the length says 10 minutes and you are 20 minutes into the show it still says 10 minutes. Is there a way to repoll this info each time you pause?

Next, using skip ahead or back skips way ahead when the show is recording, and if you skip ahead past the end of the file you end up back at the menu. This happens in the case above too. Meaning, if you skip past the 10 minutes, even though the length is actually 20 minutes it still backs you out to the menu. This also doesn't set a resume point so you may have to skip ahead several times to catch up.

Hey, When i watch a show in livetv mode, and press the record button. It starts recording the show, which is good. But when i hit stop it saves the recorded file in the livetv buffer folder.

How do i make it save it in my recordings or somewhere like that?

simple questions

untill now I'm using XP MCE 2005 with a 150MCE. Since this is not supporting analog and digital cable in the same configuration I'm looking for alternatives.

1. Does GBPVR do that?

2. could I install and run it on a xpmce OS to test it?

3. If I would use GBPVR as second programm only for using it with digital cable (sure not both programms at the same time) - could it work?

Thanks in advace! MMP

My System AMD64/3000, 512MB, Aopen Aoleus 5200, PVR 150 MCE, xpMCE

my pre-padding time is always 5 min. but the system wakeup
from hibernate only 1 minute before.
the settings in the gbpvr.mdb are correct.
whatever i set (0 min, 10 min or 30 min) the system will be started 1 minute before.

gbpvr: v. 0.23
Hauppauge-Driver :1.18.21.22301

this is the second installation with the same effect. the system is completly new with new config.xml and gbpvr.mdb

whats wrong? what can i do?

What is the best way to adjust the picture produced by the MVP? I can adjust the TV but is there a way to adjust the software of the MVP, because some images look too saturated.

Thanks

Hey

I've just started using this wonderfull program, and I just love it, very nice work all.
Since i have GB-PVR running on my server standing i my living room, i thought well lets see if it's stable, for that i fired up prime95 for about 4 hours, and well the temp got to 56C but not any higher so thought hmm lets try with folding, and as before i didn't get any higher, so thought, why not keep i running all the time, but then i can't see how folding is going inside GB-PVR so every once in a while i have to close GB-PVR and check if folding is still running and if that's the case how far it has gone.
Then got the idea to write a plugin which allows you to se the status of folding inside GB-PVR but then again i'm not much of a coder or anything the like, so can just hope someone would pick up on this idea. I think it would be cool.
Thanks for a wonderfull program and forum.

/Lars

Hello,
I have installed a new pvr-150mce and also installed the beta software for my MediaMVP. I wanted to use the scheduler that comes with the beta but when installing, it does not seem to detect the card; therefore, the scheduler does not appear.
Does anybody knows what could be wrong or if this is normal.

Thanks

download: gbpvrme.zip

update gbpvr Media Experience to support the new "My Programs" plugin. to download the emulator icons i used visit http://www.xbox-skins.net and then select the "icons" thread (its a forum)

I'm having problems getting any output. Everytime i click on the "live tv" button i get a crash in the "debug assertion failed"
..dbgdel.cpp
"_BLOCK_TYPE_IS_VALID(phead -> nBlockUse)"

I'm trying to use an Adaptec VideOh pci card.


When i running the tuning assistant the card is in the list...but it tells me "failed to find crossbar filter. Wrong device type?"

Anyone know if I can use this card, or what the problem might be?

Thanks

I have got some SVCDs which I am trying to playback through the PVR350 using GBPVR (hardware decompression). The way I play them at present is I point the Video Library to the location of the main MPEG file on the CD. It plays through the PVR350 TV Out, but the motion and sound is quite jerky. Copying the main MPEG file to the harddrive does not work any better. However, playing the file through PowerDVD or WinDVD using software decoding is very smooth... no problem.

Any ideas? Do I need to convert the SVCD to a some sort of other "MPEG-compliant format" that the PVR350 understands correctly? or...?