This is my first time on so not sure if this is the right place to post.
I am running Windows 10 in the UK. I previously used NPVR Version 3.5.7 with the following decoder settings which worked.
Renderers (Default Settings) New Settings Version 3.5.7
Video Renderer EVR EVR
Audio Renderer (Default) (Default)
Music Renderer (Default) (Default)

Video Decoders (Default Settings)
MPEG2 Video Disabled ffdshow video decoder
LAV Video Decoder does not work.
H.264 Video Microsoft DTV-DVD Video Decoder Microsoft DTV-DVD Video
HEVC Video LAV Video Decoder Disabled

Audio Decoders (Default Settings)
MPEG1 Audio Microsoft DTV-DVD Audio Decoder Microsoft DTV-DVD Audio
AC3 Audio Microsoft DTV-DVD Audio Decoder Disabled
E-AC3 Audio LAV Audio Decoder Disabled
AAC Audio LAV Audio Decoder Disabled
HE-AAC Audio LAV Audio Decoder Disabled

I have installed NPVR version NPVRsetup_3_6_6 and am getting neither picture nor sound. I have installed various codec packs including CodecSetup-74518225, ffdshow_rev4532_20140717_clsid, K-Lite_Codec_Pack_1185_Mega, SAF 631, media.player.codec.pack.v4.4.0.setup.
In NPVRsetup_3_6_6 I have uninstalled and reinstalled and tried all alternative decoder options to no avail.

Any suggestions or advice will be very welcome.

Hi Sub
I'm having frustrating issues with audio/video gradually losing sync on HDMI in with the new rocket, even using the hauppauge capture software (apparent card issue, not npvr)

So sadly I'm probably going to have to go back to component inputs, but the level on the rocket is very low, even using the latest firmware and having 'boost analog audio' selected in the config. Its also low in HDMI, but the analogue audio is super low compared to my DVB-T tuners.

So my question is, when npvr starts the rocket, can you ask the driver for a higher volume? I know that unlike the HD PVR there's no advanced settings available for the rocket in npvr. Given the small number of users that would have a Rocket I totally understand that this would be a low priority for you, but just wondering if the Rocket's volume can be set when starting it? Otherwise I'll have to dig up one my old designs for a low noise line level booster.

Cheers

Hi,

I'm hoping for some help. I've read through the posts but find anything. I have the Nextpvr Plugin on my Plex server but get the error message "This directory appears to be empty." F all the options. Is there a seeing I'm missing?

I have both Nextpvr & Plex on the same system with the standard set ups.

Thanks for any help.

Nikkie

I've run into an issue that has stumped me and I'm hoping someone in the community can suggest some things to try.

I have an HTPC setup using NextPVR with a Hauppauge HD PVR (Component Video 1080i).

This weekend I got fed up with the tangled mess of wires in my home theatre setup and spent several hours rearranging and rewiring everything cleanly.

After getting everything hooked up again, I tried using the NextPVR Live TV feature to watch a show but all I'm getting is a black screen. I haven't used NextPVR in a while so I don't know if this is a new issue or has been going on for a few weeks.

I know everything is wired correctly because the passthrough on the HD PVR is working. I have it going to the HDMI IN on my Xbox One (via a Component to HDMI converter) and I can watch TV on the Xbox without issue.

I also tested the Capture feature of ArcSoft ShowBiz (it came bundled with something I bought once, maybe the HD PVR itself) and it is working fine as well. So I know that the HD PVR is getting a signal and that it is working.

I checked my decoder settings in NextPVR and they seem fine. I'm using the Microsoft DTV-DVD decoder for H.264 and the MainConcept decoder for MPEG2.

I noticed that there was an update for NextPVR last month so I installed that but I'm still getting the black screen problem when I try to watch live TV.

Lastly, I am able to use NextPVR to watch old recordings.

The only thing that has changed recently on my HTPC is that I regularly keep my K-Lite Codec pack updated and I'm thinking maybe something with a recent update is causing issues with NextPVR. Is there a different codec I can try to use with NextPVR?

This was all working as recently as last month.

I was hoping to get back into using Next PVR for watching/recording TV on a regular basis. Is there anything else I can check or try to get this working?

Is it possible that something in my NextPVR setup is corrupted and I need to completely uninstall it and re-install?

I don't know if it matters but my HTPC is running Windows 10. I haven't had any problems with it before but maybe some new issue has cropped up.

Anyway, thanks for reading.

Hi All,
Thanks for reading this post.... Hope someone can help an ol' codger

My Tuner card is TBS6982 (brand new today) http://www.tbsdtv.com/products/tbs6982-d...-card.html
My old, now dead card was a TBS6981 http://www.tbsdtv.com/download/#tbs6981 also a DVB-S2 Dual Tuner PCIe Card

The install story for the old one is, plugged it in, turned PC on, installed drivers, install NextPVR, run next PVR.
Setup was... Devices found OK, recorder settings were... CI/CAM non. DiSEqC None. Sat Optus D1
LOF1 10750 SW 10750 LOF2 10750 (I didn't know any different)
Scanned & found all the NZ FTA channels... Wife & child happy

Skip forward 3 years... replacing 6981 with 6982 & Install story is:

plugged it in, turned PC on, installed drivers, install NextPVR, run next PVR.
Setup was... Devices found OK, recorder settings were... CI/CAM non. DiSEqC None. Sat Optus D1
LOF1 10750 SW 10750 LOF2 10750
Scanned & found no channels... Wife & child not happy

I used the blind scan tool from TBS & that found all the NZ channels (could watch them on their app too). I copied those settings to NextPVR.. No channels.
Windows firewall is off
Windows 10 home (old hardware & NextPVR were fine on here)

Logs attached.

Regards
Ralph

While I am overjoyed by the on screen mouse commands like FF and RW, would it be possible to have them stay visible for a little while longer? I am selecting FF to get through the commercials and can only get two clicks before they disappear. One work around is to constantly move the mouse to the lower edge of the screen each click and then return for a subsequent FF command. Keeping it on screen a little longer allowing perhaps 4 or 5 FF clicks would be ideal.

Thanks again for this update. I no longer have to keep a keyboard on my lap while watching a show.

Hi,

I'm new to NextPVR and started using it to replace WMC.
I noticed that some recordings are failing, but I can't find errors in the log files.
NextPVR is recording to a NAS, the computer is running W7 Pro 64 bit with a network cable connected to the same switch as the NAS is connected to. The computer can access the NAS fine. Enough free space on the NAS as well. Computer has 2 dualport USB tuners attached and all 4 tuners are configured in NextPVR.
Examples of failed recordings (all of them are series recordings and .ts files are 0 bytes):
Neighbours Eleven 16/1/2016 12:59PM-1:49PM
Neighbours Eleven 16/1/2016 12:29PM-1:19PM
Around this time other Neighbours episodes recorded fine 11:29AM-12:19PM + 11:50AM-12:49PM + 1:29PM-2:19PM

Mythbusters SBS TWO 15/1/2016 8:55PM-10:10PM
Other programs around this recorded fine as well:
DCI Banks ABC 8:27PM-10:18PM + Escape to the country 7TWO 15/1/16 9:25PM-10:47PM

Attached are the relevant ndigitalhost and nrecord logfiles, please let me know if additional information is required as I can't work out what's happening here.

So i have hopefully set up everything correctly, but probably not since this is not working for me.

in Next PVR, i can switch between all the channels and it tunes into all of them... however in KODI, the channels are listed but it will only tune into the "main" channel. i am new to this, so not aware of the terms. basically here is my list:
4.1
4.2
7.1
7.2
7.3
13.1
13.2
13.3
21.1
21.2
21.3
33.1
33.2
33.3


so if i switch to say 33.1 it will come in properly, but if i switch to 33.2 it goes to 33.1, or 33.3 goes to 33.1... etc. happens for all "subchannels" so basically KODI is limiting the channels i can watch. my TVs can all tune into the channels properly, also Next PVR app can switch between all the channels. it has to be something with KODI but i can not figure out what.

windows 8.1
KODI v15.2
Hauppauge 1196 WinTV HVR-1265 PCI Express

can anyone point me in a direction how to fix this? i would really like to use KODI as my interface but sadly it is not tuning in half of my channels.

also, the guide isnt correct.

Newbe need help getting Guide listing. NPVR working fine, all live channels OK, signed up for Schedules direct Guide shows "no show details" Have mc2xl installed, says " *bat file running, but still no details. Have dcr-2650, on device setup page no qam window appears. I have tried the Microsoft selection also with no change. Any help appreciated

In troubleshooting a problem on my android tv box I mistakenly uninstalled the nextpvr client. Now It is no longer listed in the pvr clients. If I search it is found but will not install. I am reluctant to do to much with the Chinese android box because I have no image to reinstall from.

KODI 15.2. android 5.1.1 amlogic s905 cpu, 1 gig ram, 8gig rom.

Any ideas as to how to install nextpvr client?