HDHomerun - GBPVR can not find my OTA channels

[InfectiouSoul]

^^bump^^

[sub]

Hi,

I have exactly the same issue, however my situation is probably a bit different.

GBPVR was picking up my OTA channels from the HDHomeRun without a problem on my previous laptop. That laptop died last month and Dell kindly sent me a brand spanking new one which is higher spec'ed in every department.

I reinstalled GB-PVR and the HDHomeRun software (which includes new firmware I think) on my new laptop and now it does not find any channels ("No Channels Found. Please check your signal and configuration settings"). I have not touched anything else besides the new laptop with the new software.

As per the OP, the HDHomeRun software picks up the channels without a problem and I can view them flawlessly in VLC. I also tried with Vista MCE and again it works just fine. Only GB-PVR seems to have issues with the channel (strength), even though it didn't have issues with it on my old laptop. I tried with different applications in the HDHomeRun settings (TotalMedia, GB-PVR and ATSC/Remap), all fail.

HDHomeRun Setup version 20090215
HDHomeRun Firmware version 20090215
GB-PVR v1.3.11

Attached my log files

Post your logs and I'll take a look.

What do you have the application set to in the HDHomeRun configuration?

[InfectiouSoul]

Post your logs and I'll take a look.
/QUOTE]
trying again ...

[quote=sub]Post your logs and I'll take a look.
What do you have the application set to in the HDHomeRun configuration?

and I said:
"I tried with different applications in the HDHomeRun settings (TotalMedia, GB-PVR and ATSC/Remap), all fail."

[sub]

2009-03-08 15:21:56.095 VERBOSE FindFilterByName failed to locate filter: GB-PVR PSI Parser

Try running ReRegisterFilters.bat then try again.

[InfectiouSoul]

Try running ReRegisterFilters.bat then try again.

Tried it but this gives an error:


The command prompt shows:

C:\Program Files\Devnz\GBPVR>regsvr32 /s /u GBPVRParser.ax

C:\Program Files\Devnz\GBPVR>regsvr32 /s /u PsiParser.ax

C:\Program Files\Devnz\GBPVR>regsvr32 /s /u GBPVRFlowStatus.ax

C:\Program Files\Devnz\GBPVR>regsvr32 /s /u asyncflt.ax

C:\Program Files\Devnz\GBPVR>regsvr32 /s /u GBPVRWriter.ax

C:\Program Files\Devnz\GBPVR>regsvr32 /s /u WSTSRTAnalog.ax

C:\Program Files\Devnz\GBPVR>regsvr32 /s /u WSTSRTDigital.ax

C:\Program Files\Devnz\GBPVR>regsvr32 /s /u DVBSubtitles.ax

C:\Program Files\Devnz\GBPVR>regsvr32 /s /u netasyncflt.ax

C:\Program Files\Devnz\GBPVR>regsvr32 /s /u GBPVRTSMux.ax

C:\Program Files\Devnz\GBPVR>regsvr32 /s /u scflt.ax

C:\Program Files\Devnz\GBPVR>regsvr32 /s /u GBPVRTSReader.ax

C:\Program Files\Devnz\GBPVR>regsvr32 /s /u GBPVRTSMon.ax

C:\Program Files\Devnz\GBPVR>regsvr32 GBPVRParser.ax

And stops there.

Then a seperate window opens with the following error:

"The module "GBPVRParser.ax" was loaded but the call to DllRegisterServer failed with error code 0x80070005."

Help!

[mvallevand]

If you run Vista you need to right click and run this with Admin Rights.

Martin

[InfectiouSoul]

If you run Vista you need to right click and run this with Admin Rights.

Martin

Yeah, I read that on some other thread, tried that but didn't work either.

However, I switched UAC off and then it worked (god I hate vista with a passion), rescanned and it now picks up my channels (halfway through the scan, cross fingers, knock on wood etc).

Thanks for the help, hopefully I get further now.