HDPVR - Completely Lost

[Graham]

My stb has a screensaver after 30min - 1hr of inactivity. Is there a way to pulsate a signal to the box to keep it from doing so? Perhaps setup a bat script to send 0s every so often?

Why does the screensaver not stop when NextPVR send a command via the blaster at the start of a recording or at the start of Live TV?

[hdpvr-doug8796]

Why does the screensaver not stop when NextPVR send a command via the blaster at the start of a recording or at the start of Live TV?

It requires you to hit the "OK" button. I could keep the box on by sending signal to the ir. But I would need to create a script to do so. Any suggestions? I have read it is after 8 hrs

[mvallevand]

Change your tuning script to enter an ok wait how ever long and then send the channel number.

Graham it is more than a screensaver. Typically it is low power sleep on mine a hard drive parks but in the case of fibre they might even turn off the digital transmission. It is not like copper cable or satellite which are always ending signals.

Martin

[hdpvr-doug8796]

Change your tuning script to enter an ok wait how ever long and then send the channel number.

Graham it is more than a screensaver. Typically it is low power sleep on mine a hard drive parks but in the case of fibre they might even turn off the digital transmission. It is not like copper cable or satellite which are always ending signals.

Martin

What code is OK? How do I do it?

[hdpvr-doug8796]

What code is OK? How do I do it?

"LIRC based IR Blasters can send most of the key codes not just OK. Typically with NextPVR that isn't necessary you just send leading zeroes to pad the number of digits that your STB requires or let it timeout.

Martin"

This response was made .. How would I go about doing it? Could it be done in arduino?

I found the .ir file for the remote. How can it be deciphered?

[hdpvr-doug8796]

"LIRC based IR Blasters can send most of the key codes not just OK. Typically with NextPVR that isn't necessary you just send leading zeroes to pad the number of digits that your STB requires or let it timeout.

Martin"

This response was made .. How would I go about doing it? Could it be done in arduino?

I found the .ir file for the remote. How can it be deciphered?

I assume this needs to be programmed via arduino?

OK ( Carrier 36.04 - One Time Byte Count = 0 - Repeat Byte Count = 36 )
0000 0073 0000 0012 0010 000a 0006 000a 0006 0016 0006 000a 0006 001c 0006 0010 0006 000a 0006 000a 0006 000a 0006 000a 0006 0016 0006 0010 0006 0016 0006 0010 0006 0010 0006 001c 0006 000a 0006 0c32

Why is it that the Slingbox had the ability to hit ok, but the hauppauge cannot take that code?

[hdpvr-doug8796]

I appreciate all the help. I almost have things up and running but sound wont work on 2 phones and an nvidia shield. What audio settings do I need to set?

[mvallevand]

If you are using the Android client and direct play and sound doesn't work either disable direct play or try other sound options from your hdpvr. As an example I can't use direct play with ac3 or aac except with basic stereo on several devices.

Martin

Martin

[hdpvr-doug8796]

If you are using the Android client and direct play and sound doesn't work either disable direct play or try other sound options from your hdpvr. As an example I can't use direct play with ac3 or aac except with basic stereo on several devices.

Martin

Martin

Thanks! I got it to work in kodi.