On my client, I have a microsoft remote, working with HIP.
It has worked great fo the last 18 months or so, then the other night is stopped working.

The red light was flashing on the beanbag, so it was getting a signal, but not doing anything with it. HIP seemed to be set up exactly the same.

When I ended up trying to re-learn a code, the code number for each button was a lot different than what was stored in HIP in the past.

Can anyone explain how this could happen?
I thought the IR codes would have been stored in some flash chip in the remote. (now I have to relearn each button)

While testing out my A-100, I Installed NMT install software on my laptop 1st, and now the A-100 always sees the laptop software initially rather than my HTPC , what do I remove from my laptop to stop this happening. Do I just remove the MVPMC folder? or do I also have to uninstall GB-PVR also.

My cable company is switching to all digital so I have to either setup an IR blaster with their stupid cable boxes or find another solution.

Has anyone found a good internet tv company that will completely replace standard cable/fios/dish? I was thinking some sort of internet tv company that uses set top boxes I could just feed into GBPVR.

I see the hulu, but don't see how it easily intigrates with GBPVR, and how it would stream to the MVP boxes.

all the links to the list of post message codes have been deleted....apparently they were all old enough to go by the wayside....
is there any way 'important' attachments can be kept from deletion?
i'd hate to have to upload to wiki but i guess it's ok for reference stuff..

maybe make it 2 years timeout?

Hi, I was able to get my hauppage 2250 set up in config for digital ATSC, however when I run the GBPVR app, I get audio, but no video. I know I have a decent signal, because I am able to watch shows in WinTV7, but that program is really annoying. Any advice?

Thanks,
~Ryan

Dear all,

there's a few of us working out some updated and new Wiki pages. Due to the way the Wiki works there are some limitations, but I don't mean this in a bad way, just the way it works.

For instance if I was going to upload a helpful Wiki page about setting up a DVB-S source after initial installation of GBPVR where may I put that on the Wiki so that Newbie could find easily?

For me I'd go 'Manual' then prob 'Quick Start'. But quick start page as it is does't work through my thought process currently if I was pretending to be a Newbie.

Where would you look after install of GBPVR for 1st time on how to set up, for instance, a DVB-S source?

Cheers

Steeb

Maybe I'm not searching correctly but I can't find an answer to this.

Is it possible to schedule shows to play? I'm thinking of when I'm away from the house have the TV or even the monitor to fire up, start a show either recorded or live TV with sound. That would make it look and sound like someone is home. Kinda like x10 does for lighting.

Edit: Does WinTV (blasphemy, I know) start the player to do the actual recording? It might be an option too...

Thanks,

txinga

after ticking ''enable plugins'' in config after just setting up NMT for the 1st time, I am getting this error message... error loading plugin list..., I have attached a screenshot. when I load config all the plugins have dissappeared

Occasionally, my 2250 will record the wrong program when I am trying to record my FOXHD channel. When it happens, I get my local ABC station's weather channel which is broadcast on the same physical QAM channel. This weather channel is in SD. These two channels show up as adjacent to each other in the qam scan cache file. Here are each of the channels tuning strings. The WTVD D3 is the weather channel. WRAZ HD is FOX channel I am trying to record.

T:92,0,0~P:3~TSID:1~V:81~A:84~PMT:80~PCR:81~N:>11.3 WTVD D3* (000(AC3))

T:92,0,0~P:4~TSID:1~V:33~A:34~PMT:32~PCR:33~N:>50.1 WRAZ HD* (000(AC3))

I was seeing a similar issue with my 1800 too, but I replaced it with the 2250 hoping it was just something wrong the the 1800.

I have attached some logs from I know when I witnessed the problem. It occurred at 16:00. I was trying to record an NFL game on Fox on Dec 20. I noticed it was recording the wrong show shortly after it started. I canceled the recording and then restarted it 16:12. The second attempt recorded the correct show.

Is there anything I can do to prevent this from happening?

If I pause playing back a recording on the NMT then sometimes when resuming, the video starts ok, but there is no sound. Pressing stop then play with resume usually gets back to the right point with sound.

I'm not sure is caused by the NMT or GBPVR, but I will keep my eyes open and try doing the same with PC clients and on the server..

Pause at around 2009-12-21 19:51:20 and
resume around 2009-12-21 20:02:26

both using the play key to pause/resume