Will there be any support for this card?

After following along with the suggestions in this thread, I have almost got GBPVR working how I want it. My one remaining problem is playback of the live TV buffer instead of live TV when I change from an HD to an SD channel. It's really weird, to say the least. When it gets to the end of the buffer, it exits out to the TV guide. If I change channels again before it gets to the end, the OSD shows that I've changed channels but then it just starts playing the buffered HD stuff over again.

Any ideas?

Logs attached.

The Mux checker doesn't recognize any MPG2 multiplexer, and live TV is choppy - especially the audio.

Is there an easy fix for this?

I installed GBPVR, and entered my HVR-1800 as the source on the "Capture Sources" tab. I selected "Analog Recording Plugin" with no EPG for now. The HVR 1800 I have isn't on the list, but there is a listing for HVR 1800MCE, so I used that. I have analog cable TV service.

Now, how to get channels set up??? No mention of the Tuning Assistant is made during setup. That's what I mean by "not intuitive". I happened across it, and I assume I needed to run it. I did, and it found several channels.

There are no instructions of what to do next, but I guessed that I needed to go back to the configuration. I did, but there are no channels listed on the Channels tab.

I'm stuck... I don't know what to do next, and there are no onscreen prompts or instructions.

OK this is the strangest one I have ever had. I updated to 1.3.11 on my server and client (vista64). Everything went well and it works. HOWEVER, I went to change something in config on the client and I get a virgin config screen without any of my client info on the Capture sources tab. It still has all the HUSH PC stuff in the boxes. It also shows all the default codec settings. I then went into the gbpvr directory and opened config to edit and it looks like a virgin install without any of my changes. What is really odd is that it will run pvrx2 and shows the guide and my directorys off the server. I can view shows and everything. It runs and acts like my config, but config does not show it. I don't want to reboot because I really don't want to loose all my config. Any ideas???

Hello to you all on this forum, been a regular visitor since Nov. 2007 when I built my first HTPC and chose GBPVR as the tv portal, have learnt a great deal since then and always found an answer if I was stuck here- so much so that this is my first support thread.

My problem is that on upgrade the installer failed with 'internal error 2753.config.exe' tried all the usual proceedures to repair things but to no avail- decided on a complete re-install, but no luck, still the same.

Unfortunately I could not back up the logs as even the uninstaller stalled (if you know what I mean) and I vaped the Devnez folder before engaging brain:confused: other further efforts to rescue things have also failed.

I'm afraid all is lost now, I have decided on a complete re-vamp of the whole setup.

To clarify, I am sure GBPVR is NOT my main problem, the hardware selection (Asus Pundit- AMD X2- Win XP Combo) has been a nightmare from start to finish, I could elaborate but to be fair bordem would reduce me to tears (again) and most likely every one else reading this.

My main reason for this post is that I felt it important to mention this upgrade failure just in case Sub needs the info.

Many thanks to you all for all your helpful posts- and. be assured I will be back to GBPVR soon BUT with a PROPER mainboard and case!

Im a newby at this...

I have 2 monitors but not a tv. I have been in the config app and clicked on the ratio properties. It seems as the resolution is set beyond my monitors capablities. my XP resolution on both monitors is 1024x768 but from the looks of that picture the video seems to be set 3x more than my monitors compasity ... can some one help with this problem?

my picture comes out to stretch I tryed F7
I attach an example image

hello,

I've a Hauppauge HVR 900[SIZE="4"]H[/SIZE] Tv-card
its a USB-device with a hybrid-receiver that can receive DVB-T and analoguous signals.

I was able to configure GB-PVR (1.3.11) to work with the DBT-channels, but I cant setup this nice program for the analog channels / tuner.

For this issue I added the HVR 900H to the direct.ini (analog devices ?!), and configured 2 capture devices - one fore DVB-T and one for analog on the same TV-card

Now the tuner-assistent shows me an TV-signal - but no audio-signal - because of: "ConnectPins failed" followed by a message: "Failed to connect pinNameCrossbarAudioDecoderOut to pinNameCaptureAnalogAudioIn"

For this try I modified direct.ini in the following way (filtercheck result is appended at the end of this post) - this section is a copy of the existing Hauppauge 900 Section (without H) in that file.

What can I do to enable both capture capabilities - the recorder service should switch to the analog-configuration for analog channels and to DVB-T config for all DBV-T channels

thanks

[Hauppauge HVR-900H]
ARCHITECTURE=88X
INIT_MODE=DEFAULT
INIT_MSP=0
SUPPORTS_FM_RADIO=1
BLACKBIRD=1
CONEXANT=0
ENCODER_DISCONNECT_BUG=1
FORCE_ENCODER=1
FILTER_CROSSBAR=WinTV HVR-900H Crossbar
FILTER_CAPTURE=WinTV HVR-900H Capture
FILTER_TV_TUNER=WinTV HVR-900H TVTuner
FILTER_TV_AUDIO=WinTV HVR-900H TVAudio
FILTER_CAPTURE_AUDIO=
FILTER_ENCODER=MainConcept (MCE) MPEG Encoder
PIN_CROSSBAR_VIDEO_TUNER_IN=Video Tuner In
PIN_CROSSBAR_AUDIO_TUNER_IN=Audio Tuner In
PIN_CROSSBAR_VIDEO_DECODER_OUT=Video Decoder Out
PIN_CROSSBAR_AUDIO_DECODER_OUT=Audio Decoder Out
PIN_TVTUNER_ANALOG_VIDEO_OUT=Analog Video
PIN_TVTUNER_ANALOG_AUDIO_OUT=Analog Audio
PIN_TVAUDIO_TV_AUDIO_IN=TVAudio In
PIN_TVAUDIO_TV_AUDIO_OUT=TVAudio Out
PIN_CAPTURE_ANALOG_VIDEO_IN=Analog Video In
PIN_CAPTURE_ANALOG_AUDIO_IN=Analog Audio In
PIN_CAPTURE_PREVIEW_AUDIO_OUT=Video Virtual Out
PIN_CAPTURE_CAPTURE_OUT=Capture
PIN_CAPTURE_I2S_OUT=Audio
PIN_CAPTURE_656_OUT=Capture
PIN_ENCODER_I2S_IN=Input Audio
PIN_ENCODER_656_IN=Input Video
PIN_ENCODER_OUT=Output
PIN_WRITER_INPUT_IN=Input


FilterCheck.log:
19:46:01.437 INFO Log started
19:46:01.437 INFO Filter Check v1.0
19:46:01.437 INFO
19:46:01.437 INFO
19:46:01.437 INFO Checking AM_KSCATEGORY_CAPTURE filters
19:46:01.500 INFO found: SoundMAX Digital Audio
19:46:01.515 INFO - (input) DAC
19:46:01.515 INFO - (output) DAC
19:46:01.515 INFO - (output) Aufnahme
19:46:01.515 INFO - (input) ADC
19:46:01.515 INFO
19:46:01.515 INFO found: Logitech QuickCam Communicate
19:46:01.546 INFO - (output) Capture
19:46:01.546 INFO - (output) Standbild
19:46:01.546 INFO
19:46:01.546 INFO found: Logitech Mic (Communicate)
19:46:01.562 INFO - (output) Capture
19:46:01.562 INFO - (input) Mikrofon
19:46:01.562 INFO
19:46:01.562 INFO found: WinTV HVR-900H Capture
19:46:01.562 INFO - (output) Capture
19:46:01.562 INFO - (output) VBI
19:46:01.562 INFO - (output) Audio
19:46:01.562 INFO - (input) Analoger Videoeingang
19:46:01.562 INFO - (input) Lautstärke
19:46:01.562 INFO
19:46:01.562 INFO
19:46:01.578 INFO
19:46:01.578 INFO Checking AM_KSCATEGORY_ENCODER filters
19:46:01.578 INFO
19:46:01.578 INFO
19:46:01.578 INFO Checking AM_KSCATEGORY_CROSSBAR filters
19:46:01.578 INFO found: WinTV HVR-900H Crossbar
19:46:01.593 INFO - (input) 0: Video Tuner In
19:46:01.593 INFO - (input) 1: Video Composite In
19:46:01.593 INFO - (input) 2: Video SVideo In
19:46:01.593 INFO - (input) 3: Audio Tuner In
19:46:01.593 INFO - (input) 4: Audio Line In
19:46:01.593 INFO - (output) 0: Video Decoder Out
19:46:01.593 INFO - (output) 1: Audio Decoder Out
19:46:01.593 INFO
19:46:01.593 INFO
19:46:01.593 INFO
19:46:01.593 INFO Checking AM_KSCATEGORY_TVTUNER filters
19:46:01.625 INFO found: WinTV HVR-900H TVTuner
19:46:01.640 INFO
19:46:01.640 INFO
19:46:01.656 INFO
19:46:01.656 INFO Checking AM_KSCATEGORY_TVAUDIO filters
19:46:01.656 INFO found: WinTV HVR-900H TVAudio
19:46:01.703 INFO - (input) TVAudio In
19:46:01.703 INFO - (output) TVAudio Out
19:46:01.703 INFO
19:46:01.703 INFO
19:46:01.703 INFO
19:46:01.703 INFO Checking AM_KSCATEGORY_VBICODEC filters
19:46:01.718 INFO found: NABTS/FEC VBI-Codec
19:46:01.750 INFO - (input) VBI
19:46:01.765 INFO - (output) NABTS
19:46:01.765 INFO - (input) HWNABTS
19:46:01.765 INFO
19:46:01.781 INFO found: Untertiteldecoder
19:46:01.812 INFO - (input) VBI
19:46:01.812 INFO - (output) CC
19:46:01.812 INFO - (input) HWCC
19:46:01.812 INFO
19:46:01.812 INFO found: WST-Codec
19:46:01.875 INFO - (input) VBI
19:46:01.875 INFO - (output) Videotext
19:46:01.875 INFO
19:46:01.875 INFO
19:46:01.875 INFO
19:46:01.875 INFO Checking KSCATEGORY_BDA_NETWORK_TUNER filters
19:46:01.906 INFO found: WinTV HVR-900H BDA Tuner
19:46:01.937 INFO - (input) Input0
19:46:01.937 INFO - (output) MPEG2-Transport
19:46:01.937 INFO
19:46:01.937 INFO
19:46:01.937 INFO
19:46:01.937 INFO Checking KSCATEGORY_BDA_RECEIVER_COMPONENT filters
19:46:01.984 INFO found: BDA Slip De-Framer
19:46:02.031 INFO - (input) NABTS
19:46:02.031 INFO - (output) IPv4
19:46:02.031 INFO
19:46:02.046 INFO found: BDA MPE-Filter
19:46:02.062 INFO - (input) MPE
19:46:02.062 INFO - (output) IPv4
19:46:02.062 INFO
19:46:02.078 INFO found: WinTV HVR-900H BDA Capture
19:46:02.171 INFO - (input) Input0
19:46:02.171 INFO - (output) MPEG2-Transport
19:46:02.171 INFO

I cant find my new Hauppauge WinTV Nova-T 923(909) in the tuning assistant
so what do I use to scan the channels?