2008-11-18 22:08:49.090 ERROR [7] Media stream thread caught exception: System.IO.FileNotFoundException: Could not find file 'C:\Program Files\Devnz\GBPVR\forcefailure'.
File name: 'C:\Program Files\Devnz\GBPVR\forcefailure'
at System.IO.__Error.WinIOError(Int32 errorCode, String maybeFullPath)
at System.IO.FileStream.Init(String path, FileMode mode, FileAccess access, Int32 rights, Boolean useRights, FileShare share, Int32 bufferSize, FileOptions options, SECURITY_ATTRIBUTES secAttrs, String msgPath, Boolean bFromProxy)
at System.IO.FileStream..ctor(String path, FileMode mode, FileAccess access, FileShare share)
at GBPVRX2.MVP.x3ca133dee7547455.xf9d81bb81f7c2ff0()
Just gets a blank screen - I'm still on the august firmware. But if I reboot the pch, and navigate though the the pch interface to the same file, it plays... Any ideas?
Hi All,
I'm new to this forum, but after suffering this problem for several days and having just had the same problem occur following a complete hard drive re-format, I am officially stumped...
I have been using GBPVR for several months now, and until recently it has usually worked fine. About 10 days ago when I scheduled a program to record it failed to do so. Accessing the PVRx2 program, under the recording menu there was no record of it. When I was looking through explorer, I noticed there was a folder in the relevant directory, and there was a file under that folder which corresponded to the programme that I had scheduled to record. Double clicking this opened media player where the image was scrambled but I could hear the sound fine (always had the scrambled pic when trying to watch on another program, so not too bothered by that). By going back into PVRX2 and accessing the file through the Video Library tab, I was able to watch the programme. Although as the programme went on the sound and vision seemed to go further and further out of sync. Most confusing.
But it gets worse. Since then, when I try to record several shows in a row, it will record 5.6kb of the first one, and fail all the subsequent ones. But then sometimes it records just fine.
It seemed to start just after I had networked my xbox to my PC, so I thought it was something to do with file sharing, or the firewall, or maybe it was because I had an older version of GBPVR. I updated GBPVR to the latest version, and it kept happening.
I decided that as I was due a reformat I would start fresh, with file sharing turned off. So I've just spent the last 6 hours sorting out the whole pc, only to find that it's doing the same thing as before.
My head is frazzled, I'm at my wits end, and if it doesn't get sorted soon this damn machine is going through the window... PLEASE HELP!!!!
Hi, had only just updated to 1.3.7 last night and I'm reporting in with some probs with the timeline (and 'timebar').
I've seen a couple of other threads - eg 38702, 38677 which cover a similar area but thought worth mentioning my symptoms (also with that latter thread, there seems to be a lot of suspicion about the .TS filesize being an issue but I think that has no bearing in the cases I've looked at).
I played several recordings (.TS files made previously with 1.2.13) and have seen these problems:
- The initial start time can be totally bogus
- I played a 1hr15min recording and the end time was listed as 21 minutes
- Navigation (ctrl-arrows, ctrl-D,F) jumps unpredictably
- When I started one recording, the two 'seconds' digits started ticking over really fast as if they were 1/100th seconds
One good thing - ctrl-Q (resume from pause) resumed immediately (often it didn't with 1.2.13), however it resumed to totally the wrong place.
I know in the past I've had some timeline problems with broken streams, but now with 1.3.7 all previous recordings (including those that were good) are broken in one way or another (but which symptom they show is really unpredictable).
I've gone back to 1.2.13 and things have stabilised.
My System: Intel core2quad, 2GB, 8500GT video, hvr2200 cap card.
Frank, I don't know if you can interface to vlc but this will create a mvp compatible mpeg from an encrypted dvd D: is my drive dst is the destination. I was using it with mvpmc native interface for a while and it works ok. You can add it as a custom task if it is setup properly.
I recently tested the NMTinstaller and reinstalled MW (latest) but am now getting dotNet errors? Can you see what the issue might be from the attached?
I was watching DWTS and live it looked fine, so I pressed the record button. Came back later to watch the recorded file, nothing but blue screen and hiss! It is an .mpg file - I thought HD was supposed to record directly to disk in a .ts file? Mabye I'm totally off, so any input would help!
OH - and the TV buffer is working, because I can pause and play at will.
Hi folks
I was wondering is it possible to use the html pages Created by My lil Movie Jukebox Through GBPVR on the popcorn. That way I will have everything running through GBPVR and not jump around using different methods.
thanks
David
I use PVRX2 to open DvbDream satellite viewing program. I want to be able to control DVbDream with the Hauppauge remote control while the app is open and return to PVRX2 control when the app is closed. Is there a way to do this?
Periodically PVRX2 freezes, and stops responding to all input. I have to either reboot the box (wife's method) or hit ctrl-alt-delete and kill the process. It could be my graphics card is finally dieing, but I'm not real sure. I have attached the logs. I see errors in some of the logs and a bunch of "database flush"
Looking at a dvb-s scan cache entry that I found on the forums, the tuning data for one particular channel is shown as
Code:
T:10773,H,22000,56
from this I've worked out that the carr. freq. is 10773, symb. rate is 22000 and polarization is horizontal. At that point I'm OK.
I've also worked out that 56 is an FEC Rate of 5/6 but looking at the DirectShow DVBS Network Provider, I see it has an Inner and Outer FEC Rate setting. Which one applies in this case or is it both?
Also the DVBS NP filter has a 'West Position' parameter is this important and if so how do I know what to set depending on a particular satellite?