If if is not happening, at least remove it from the feature list. I think I've been fairly patient up till now.
One year from now the analog broadcasts will be shut down here in Denmark and then we will be forced to seek alternatives to GBPVR which do support DVT-T subtitles.
Sub, could you please let us know if you plan to get them to work again within the next year or not ?
I will happily supply streams for you to test on, of course.
I am trying to enlarge the rectangle that shows information in the miniguide, while I've found the skin file for OSD and TV Guide, I can't seem to figure out where the mini guide skinning is located at.
I have ditched Sky TV due to lack of use. I was using it in conjunction with a ATI 550 card for my HTPC.
I have since swapped that out for a HVR4000 that was used for DVB-T in another machine.
I have no experiance with DVB-S and was hoping someone could give me a few pointers.
Firstly, in the source config, which sattelite will give Freeview??
I am using the existing Sky dish, and have no idea how to apply the LNB value read off the dish to the config.
Does the dish need a power supply, and if so, does the HVR4000 supply this??
As an aside, I noticed that I am still getting the FTA channels from the Sky decoder includeing Prime. Can I tune into these useing the HVR if they are not encrypted??
I have MovieWizard 1.0.20.2 installed and I go into the settings to setup the Target Extensions and check off the SubDirs box, when I exit and re-enter the plugin settings they aren't saving any new additions. I have been trying to add .mkv and .mp4 but it isn't saving them. Anyone else experiencing this problem? Thanks.
I have a PVR-150 and a PVR-500 isntalled in my machine and I had to setup an epg with each one in config. I think that's just to get a channel line up for the tuner being setup?
Tonight I wanted to empty the epg and reload it. It appears that emptying the PVR-150 (the first tuner in the system) epg clears the TV Guide displayed in GPBVR and reloading it also reloads the guide in GBPVR.
Question - do a I need to empty the epg on each tuner and reload it or does it not matter which one you empty/update as they all write to the same file?
I was scanning my TV Guide just now and I noticed my highlight disappeared, i tried moving left and right and it would appear and disappear.
I finally found that some of my channels have two shows listed at the same time, the first doesn't show up with a highlight or on the grid but do on the program description below. The show line up is also skewed, it's like Schedules Direct listed two shows at 7pm when one would have been at 7 and one at 8pm.
Example:
Channel 3, KMTV, CBS out of Omaha, NE should be NCIS at 7pm, Without a Trace at 8pm, 48 hours mystery at 9pm, and the news at 10pm
What I'm showing is NCIS not being highlighted or showing up on my grid but it showing up at the bottom in the description area. Pressing the right arrow then shows Without a Trace in the 7pm grid and it's highlighted. Pressing it again shows 48 Hours Mystery at 8pm, and pressing it again shows the news at 9pm.
I just installed EPGExtra last night so I wondered if that was causing a problem, but I went to the config and emptied the guide (and confirmed it was empty) and then reloaded. EPGExtra doesn't run unless you run it manually or it's called from postupdate.bat and postupdate evidently isn't called when updating from the config as the extra info didn't show up in the reloaded guide, but the guide was still showing the screwed up shows. Running the postupdate batch file afterwards restored the extra info.
Soooo, do I take it that this is a Schedules Direct problem and not an issue with my setup?
Schedules Direct seems to have been a bit off lately - I've found a few shows that aren't correct (such as Star Trek Voyager which was supposed to be on Spike in the mornings), but this is the first issue with two shows listed at the same time I've found.
Is this unusual for Schedules Direct or should Ilook for another guide source (there really isn't one here in the US, is there?).
I am new to the forums and to gbpvr. I have previously been using 2005 Win MCE XP with an ATI 9600 XT AIW card. I just bought a Hauppauge 1600 card for clear QAM broadcasting on my Comcast cable. I installed gbpvr last night and managed to find all my channels digital std (480p) and HD (720p). However, some of my HD channels have video/audio stuttering problems while others don't. I have tried switching between different video encoders Cyberlink, InterVideo, ATI, and default with no luck fixing the problem. Any help would be appreciated.
Let me start by saying I've never had a need to use this. I use the Hauppauge MCE remote and the default settings for it within GBPVR have always worked for me but I'm considering trying to use something like HIP if I can program some more complex tasks into it. My main reason is trying to eliminate the use of the keyboard altogether for some tasks. Not a problem for me but some members of the family find this difficult. I know I've read that you can use HIP to utilize the Green Button on the MCE remote to launch PVRX2 now would it be possible to program buttons to close it or to open other programs?
I would like to be able to program the remote to hit one button to open PVRX2, one to close it and one to open PowerDVD so that if someone wants to watch a Blue Ray movie the only need to hit one or two buttons to do that. I just don't know if this is something you can do. If it has to only be controled by GBPVR so if you were to close it it would not be able to open another program. Anything like this.
One other question, sorry, if I use this software to do all of this. Can I just set some options for a couple buttons and keep the rest the same or do I have to remap the entire remote?
