Sunday's Nascar race recorded just fine although there weren't any shows scheduled back to back with it. Last nights Prison Break was broke into three files right at the end of the show and then two files were created for Terminator with only a few hundred KB of data in each and then it quit recording altogether. Never got any error except I noticed when we tried to watch Terminator while it was recording that nothing would play and in the TV Guide it wasn't marked red like it hadn't been scheduled to record.
This was on 2/18 with Prison Break at 7pm and Terminator at 8pm.
Also, is there a way to keep "Stopping screen saver from kicking in..." from being logged once a minute and filling up the logs?
I have an immediate problem that, with three input sources (a dual DVB-T and a DVB-S2), the "Show Status" of the GB-PVR tray tool only shows the status of the frist two devices - the remaining one is beyond the popup window - which is of course not resizable!
Any cures (short of using less devices)?
In general tho' its irritating that the GB-PVR on-screen texts are so huge that the guide is barely usable and the info about a viewed program in live TV scrolls off the bottom of the screen. The PVRX2 sizes are far better. It would be nice if there were a seting on the config panel to stop GB-PVR from "shouting so loud".
Hi. I searched the forum and read the sticky's but could not find an answer for this. I am a noob when it comes to PC based TV.
My system: Intel Quad Core 2.4; 4 GB Ram; Vista Ultimate 64 bit; Hauppauge HVR-1600; Hooked up to Bell ExpressVU
I know....I made a blunder with Vista X64...but have to live with it now.
My Problem:
1) If I run the "tuning assistant" it finds channel 3 from my satellite receiver and the correct show is playing and the quality is very nice
2) I have run the "Config" utility and updated the EPG from CT TV. The channels all populated, complete with descriptions and manually added channel 3, found by the tuning assistant.
3) When I go back to GB-PVR and click on Live TV, it tells me that I have to run the config utility and force the EPG to update, which I have done.
It refuses to recognize that the EPG has been updated with channels.
Anyone have a solution? I am sure it is something simple that I am missing, but I have spent hours on this and am very frustrated.
On a PVRX2 box I have configured as a client, the aspect ratios all work using the F7 key except "Remove Letterbox". And of course this is the one that I need! Can I tweak something to make it work? Thanks.
My conclusion that I had Acamd working with GBPVR (http://forums.nextpvr.com/showthread.php?t=33120) was wrong. It worked, but for some reason it stopped working (no picture) and it's going on and off now, so it's not stable or reliable yet.
On http://forums.nextpvr.com/showthread.php?t=33309 you are discussing a new MDAPI and I've seen the subject on dvbn.happysat.org.
What I'd like to point out that Acamd is working perfectly with ProgDVB, so I wonder what the difference is with GBPVR? Is ProgDVB using a different MDAPI, or something completely different?
After forced reconfiguration (warn out system drive) playback via both my mvp's is choppy. Before the reconfiguration it was working fine. Playback directly from the the box via GBPVR is also chobby, PVRX2 not working (no Wrm9 support), WMP only plays sound.
Have installed nvidia decoder (trial version). Using overlay manager, under misc settings: cyberlink muxMy "active system process" constantly is about 95-99% in "idle" condition, cpu use varies between 0-6%, Allocated memory of 395M. When activating playback via mvp i can hardly see any change in cpu use, but still chobby playback.
Have tried going through hole thread "disappointing MPEG2 decoding" following the vaious suggestions (9.0b quartz.dll ao.) however no positive result. Im close to giving up, and starting all over again - as someone suggested without going through the various windows updates, however would like to hear if anybody has any suggestionsHavent before i start all over again?
I have an Aver media M780 card that is supposed to receive digital cable programs. I can get the standard cable without a problem. I have tried in the configure program to set up a new configuration use the Aver media M780 'bda recording plug-in'
I can not get any digital stations. I have tried with the 'avermedia m780' and the 'avermedia m780 qam' source plug-in. The last tried was the 'avermedia m780'
Got my GB-PVR setup over the weekend. Running the latest version through a WinTV Nova 500 dual card on an XP SP 2.0 dedicated box in the lounge.
Great bit of software btw
Got most of the problems I encountered ironed out, save a small one regarding .Avi's.
From what I have gathered over the last few days, the 500 has built in MPEG hardware Encoding\Decoding. This is great if you have a library of mainly MPEG films. Unfortunately most of mine are DivX or Xvid. When I play a DivX film, I do not get the progress bar, nether can I pause or fast forward the film. I take it that this is due to the film being decoded and played on the fly?
My only gripe with this is, if I stop a film half way through, I then have the problem of not being able to skip to the point I last watched.
Initially I thought this may be a bandwidth problem, since the films are held on my main machine in the other room and piped into the lounge via my wired 100baseT network. So, I copied the film locally and played it - same problem.
Do others suffer from this problem?
Do you transcode the film withing the film library into another format before playing?
I know I could recode all my films into MPEG, but that would take forever (have hundreds of films etc) - suppose it is an option though.
I installed the latest version of the DivX codec's off the net, the rest of the software used is as up to date as I could find - with the exception of the clunky hauppage software supplied with the card.
Oh, also, if I let the film play till nearly the end, I still do no have the ability to pause. So it seems it's always decoding the part just before I watch it.