Hello,

I've just discovered GBPVR (great program), I am using a ".exe" program to change channels. The trouble is I think the channel commands are being sent too quickly, I have introduced a delay using the parameters for the ".exe" program but I can't put a delay in between channel digits. Is there any way to do this?

Thanks,
Martin.

Where is the option in the config prog to enable/disable the PVR350 TV out... my installation seems to be convinced that I've selected pvr350 tv out mode and I can't see where to turn it off for the life of me....

Ta

M

Any chance that you're considering hardware MPEG-4/DivX encoding with the Plextor PX-M402U? I think that the first PVR with a decent UI that supports hardware based MPEG-4/DivX will become an instant favorite. Sure the PX-M402U is just one device and others will come - But look how many people have bought a PVR-250 just because someone decided to support it. Someone has to bite the bullet and add support for this device, even if just to be the first one out of the gates with hardware MPEG-4/DivX. "If you build it, they will come..."

- Hi-Speed USB 2.0 Video Capture Peripheral
- Composite Video, Composite Audio and S-Video Inputs
- Hardware Encode to DivX®, MPEG-4, MPEG-2/DVD, MPEG-1/VCD   Formats
- Includes InterVideo WinDVD Creator 2 Video Editing and DVD Authoring Software
- Hardware and Software Certified by DivXNetworks

op

I sent version 1.22 to sub and it should be available soon.  It appears pretty stable now, so I will clean up the code a little then put it here as well.

I think I will be starting on commmercial skip next and let someone with more ASP experience than me tackle the web interface

Sub,
It's time to give you a bit of feedback on v016 after having had some time to test it a bit. Although the general status is VERY good, there are some minor issues that I thought were good to mention to you:

Duration of recordings always shows 00 hours, even for longer recordings (already in v015, maybe even older versions)

Yellow button doesnt work for m3u playlists: I can't queue two albums.

Volume control doesnot work (music/video) although the release notes says they should work. Maybe I'm doing something wrong.

There is an inconsistency with the use of the pause button. It pauses video AND music playback. It resumes video playback, but music playback can only be resumed with the play button.

I can start wmp form gbpvr (custom task that also starts ir.exe and puts gbpvr in the background) to watch a dvd. However playing a dvd this way gave clicking sound when using vmr9 in gbpbr. With overlay there is no problem.

With pause/livetv the skip fwd/bwd doesn't work, though according to the release notes it should.

To conclude this post a tip:
In the current setup skipping forward and backward in video playback requires many buttonpresses (number of seconds, skip). So to skip 5 minutes (a commercial break) you first must calculate 5*60 =300, then press 3 0 0 skip.
Another strategy is to skip minutes. 5 minutes is then 5 skip.
To allow for smaller skips, parts of a minute should be preceded with a zero: so 30 seconds (=half a minute) means 0 5 skip.
I think this reduces the number of keypresses considerably and is also more intuitive.

Greetings,
MaBo
(Setup: pvr350, tv-out to tv, no ir.exe running)

Hello,

I just tried to update from v0.14 to v0.16 (i thought it was time for an update, and see what's new, everything worked for me before, well, as far as everything can work if u use the PVR 350 tvout)
But now im stuck at configuring the capture sources, when i add one, and add the correct recording source, and EPG source. Then i close the program (by clicking twice on OK). And open it again, so that can update EPG, but when i open the program again, then the line in capture resources is gone :/. I guess im doing something wrong, cause i seem the only one with problems with this. I looked at the documentation, but that couldnt help me.

I'm not implementing it just yet, but how do you think "favorites" should work if they were added to GB-PVR?

Sub

Are you still looking for someone to do a virtual keyboard?

I'd be happy to pick it up.

Dai

Hi,
I have just got hold GB-PVR (which looks great by the way).

I am having a couple of problems getting it going!

1) I have a Hauppauge PVR250, yet I can't select the 350 driver in the config - When I run GBPVR I tells me there is no available 350 board.

2) If I click on Live TV I get the message 'Failed to communicate with the GB-PVR recording service, this software is possibly not running'.... etc.

Any ideas?!?

I have done the usual restart, update drivers etc. but with no joy.

I got really excited when I saw this program as I have been trying to get ShowShifter to work (with no luck, as it does not fully support the PVR250).

Some help would be great

Cheers guys/gals

I set the file name, hit OK all the way until the config app terminates. But when I go back into the config app to update the EPG, that field is blank and the update button gives me an error telling me it is blank.

I can, however, set the file and do an update EPG immediately and it works. The file name apparently isn't being saved