i5-4460, 8GB, ASUS H87M-E, 2 x Hauppauge 1229 WinTV-HVR-2255 Dual TV Tuner / Encoder - OEM, 240GB Kingston SSD, Win 7 Home Premium-64, ASUS BluRay RE drive, Antec 650 Platinum PS (93% efficiency) in a SilverStone ML03 case.
The software is running and recording, so far it's only been recording with 1 tuner, as it is, I'm using the guide to add shows, but setting the EPG for 8am update only gets to about 7pm for most of the channels and then I have to manually re-scan it. IS there a plugin to force more than 1 EPG update a day? At say 2pm, it should get the rest of the day to 11pm (which is fine). Also, what I was hoping, was to be able to tell the unit, turn off after the last recording for the night. I have a 7:59AM boot in the BIOS, so it will boot up daily at that time, giving it a minute to boot (takes a lot less than that) so the EPG can be done at 8AM.
Now some will say "Are you nuts having that i5 in there, not to mention that 650 Platinum PS" and I'll answer "No", the reason is, the air cooling is "PASSIVE" in the case, the only fan in there is the CPU fan, nothing else. The power supply's fan is just for itself (and sadly, not as quiet as I'd hoped, but because it's less than 1CM from the shelf, the noise is elevated due to accoustics). The system running at full use for the duration of burn-in (built the system on Friday last week) got the board to 90F and the CPU to 101F.
I plan on using ComSkip in parallel to all the tuners that are recording, to catch commercials, but before I get there, I really need to get this TV Guide issue resolved (and the graphics part of it too).
What happens (Active Skin is Default):
Show TV Guide, go somewhere else, click the Menu button, either it slides out and shows up properly OR it slides out UNDER the TV Guide (unreadable). Or, I click to somewhere other than the TV Guide (after having it open), click on the Menu and the TV Guide pulls up over top of the menu and where I last was.
Stopping Live TV:
The "Please Wait" window never vanishes, unless I click somewhere outside of it. I left it for an hour at one point, it never came out, until I clicked outside of it, then it vanished. Tried turning Sync on and off with no change, both this system (my desktop) and the new above HTPC exhibit the same things, so it's not hardware related.
My major issue now is, not being able to re-fire the EPG scan more than once a day.
Does it work with NPVR or am I running into a brick wall? I need a remote as the HTPC hybrid sleeps when not in use and without a USB device to wake it up, it stays off and requires the power button pressed to wake it up. (Oh and I didn't plug any of the lights in, like I need blinking lights glaring at me while watching TV recordings, wish I could turn the BluRay drive's light off.)
I have setup NextPVR on a Windows 10 machine as a server. I have enabled web server and kept the 8866 port and default username and password. Under the XBMC the access pin is at the default 0000 and also allows remote access.
When I am on my Windows 10 Machine (which is running NextPVR) i can access the web portal by going to https://localhost:8866
When I try to access the web portal on my MacBookPro by accessing the same address or https://127.0.0.1 it will not allow me.
I installed the NextPVR client on my OSMC Raspberry Pi Machine and entered the same credentials in the PlugIn settings and it cannot access the NextPVR server, so no go on TV on the Pi.
Any help or advice on the proper settings or setup for this to work with the Pi or even other machines?
BiostarG41D-M7 mobo
Core2Duo @ 3.0 Ghz.
4GB DDR2
XFX Radeon HD 5450
1.0 TB Seagate (primary)
250 GB Seagate (secondary)
Windows 10 Pro 32-bit
I am about to receive a Ceton Infinitv 4 USB, which I will be using with cableCARD via Comcast. My primary concern at this point is drivers, which I have been unable to install under Windows 10, even using Windows 7 or Windows 8 compatibility. I already know that I will only be able to receive "copy freely" programming, and I have no problem with that. The biggest headache, in addition to drivers, is that Ceton's installation software insists that WMC MUST be present in order to install the drivers, due to DRM issues. Given all of this, is there any way that the Ceton will work with nextPVR, or do I need to go to a Linux-based solution, such as Mythbuntu? Since I'm on SSDI, right now I simply can't afford an HDHomeRun, or anything similar. If there's any way that I can use the Ceton with nextPVR, please let me know! Thanks in advance for any help or advice.
I'm having a similar problem to others on this forum. I've searched and tried everything in threads I could find regarding this issue.
I get certain blanks channels when viewing live TV thru NPVR app. It's only about 3 of the 13 OTA channels that are affected. The channels affected all have about 70%+ signal strength.
Some of the channels work sometimes and then when I hit one that doesn't, the channels three affected don't work. The channels are 8.2, 15.2, and 43.3 (8.1, 15.1 and 43.1&2 always work!)
So far, I've downloaded the CCCP and SAF 6. I've enabled the NPVR programs through the firewall for public and private. I'm almost certain it's a decoder issue. The channels work fine in the HDHR view app all the time. As well as VLC through the HDHR config. (The channels also don't work in Kodi but I figure it's a related issue as I'm using the NPVR plugin for Kodi.)
The options I have for decoders are:
mpg2: LAV Video Decoder, Cyberlink Video Decoder (PDVD10), Cyberlink Video/SP Decoder (PDVD10)
h264: LAV Video Decoder, Cyberlink Video Decoder (PDVD10), Microsoft DTV-DVD Video Decoder
I've attached my log and a 1min .ts file to see if it plays (it's NOT 0kb but it doesn't play for me in VLC).
Please, let me know what to try next. Thanks!
(Windows10)
I just changed my audio setup from stereo only with two front speakers to 5.1 with a sound bar (vizio). WAF plunged because the center channel fades in and out throughout the show. Any ideas on how to cure this?
Setup: computer HDMI -> Panasonic plasma ->spdif ->soundbar. Using LAV decoders.
There are various ways in which the UI of NextPVR could be improved to make it easier/quicker to use:
1. On the screen which displays live video, add -/+ buttons to change channel, and allow digits to be used to enter a channel directly (eg press 3 3 and, after a suitable inter-digit timeout, it changes to ITV1+1, channel 33). Also add a Record button which instantly starts recording the channel which is currently being watched.
2. When displaying the TV Guide, implement a search facility (search by programme title) and again allow a channel number to be entered digit by digit to move the focus vertically to show listings for that channel and those numerically adjacent to it.
3. On Recordings | Ready Recordings and Recordings | Pending Recordings, if the mouse is on top of a recording or timed event, make a right-click bring up the Close/Play/Delete menu as an alternative to having to double-click on the entry to display this menu. If the cursor is anywhere else on the screen, bring up the existing right-click menu Open File / Live TV / Main Menu / Channels.
4. In general, in all situations where a menu selection would delete a timed event, stop a recording or delete a recorded program, insert an "are you sure" clarification to guard against accidentally clicking on the wrong menu item.
5. When double-clicking on a pending event which is currently recording, change the menu item "Cancel" to "Stop Recording" (with "are you sure" confirmation) as the latter wording is a more accurate description of what will happen.
I would like to alter a "Scheduled Recurring Recording" from "New Episodes" to a Day And Time.
I bring up the required Recurring Recording and select "UPDATE".
I then go to Recording Type and try to change it ..... but no go
Pre/Post Padding and Keep all work.
I also have a question on how NEXTPVR determines if an Episode is NEW or OLD.
I have quite a few shows with ENCORE in the description column and would like to mark them as NOT NEW
I've posted everywhere as I've taken 3 trips to the service center and 3 nights on calls with no luck getting a cablecard working in the HDHR Prime.
They want to charge me for a tech visit, I'll just return the equipment and stay with DISH.
The issue is when I bring up HDHR http://192.168.150.121/lineup.html, I see a DRM symbol on all channels.
No channel will stream thru VLC with that set.
No one at the end of the phone can fix it.
Anyone here have any suggestions?
