Terratec Cinergy 2400i DT initial configuration problems

[nia]

Probably something to do with this:

PHP Code:

2007-03-29 12:50:48.656    ERROR    [5]    Error starting recording: System.AccessViolationException: Attempted to read or write protected memory. This is often an indication that other memory is corrupt.
   at ConnectPins(IGraphBuilder* pGB, IBaseFilter* pSourceFilter, Char* pinNameSource, IBaseFilter* pDestFilter, Char* pinNameDest)
   at NativeUtilities.BDARecorder.RenderToInterVideoMux(Int32 videoPID, Int32 audioPID, IBaseFilter* demuxFilter, Char* pszFilename)
   at NativeUtilities.BDARecorder.StartRecording(String cardType, Int32 board, String filename, IntPtr hwnd, ChannelTuning channelTuning, Int32 lnbLOF1, Int32 lnbSwitch, Int32 lnbLOF2, Int32 diseqc, Boolean powered, Boolean previewMode)
   at NativeUtilities.BDARecorder.StartRecording(String cardType, Int32 board, String filename, IntPtr hwnd, ChannelTuning channelTuning, Int32 lnbLOF1, Int32 lnbSwitch, Int32 lnbLOF2, Int32 diseqc, Boolean powered)
   at GBPVR.Backend.Common.BDARecordingSource.startRecording(IRecordingSourceConfiguration config, Int32 qualitySetting, String filename, ChannelTuning channelTuning, Int32 minutes, Boolean useStreamingEngineIfAvailable)
   at GBPVR.RecordingService.x93f60a55016d55c4.xcba1f05fb5a46d5f()
2007-03-29 12:50:48.656    INFO    [5]    Found new programme requiring recording: Frasier
2007-03-29 12:50:48.687    VERBOSE    [5]    Changing to channel (GBPVR.Backend.Common.NullTunerController): 167
2007-03-29 12:50:48.687    VERBOSE    [5]    Requesting IRecordingSource to start recording: D:\PVR\Recordings\Frasier\Frasier_20070329_00350105.mpg
2007-03-29 12:50:48.703    VERBOSE    [5]    DirectRecordingSource about to start recording  oid:1 channel:167
2007-03-29 12:50:49.250    ERROR    [5]    Error starting recording: System.AccessViolationException: Attempted to read or write protected memory. This is often an indication that other memory is corrupt.
   at FindFilterByName(_GUID* refCLSID, Char* decoderName, Int32 instanceRequired)
   at NativeUtilities.ConexantRecorder.StartRecording(String cardType, ConexantRecordSource recordingSource, Int32 qualitySetting, Int32 board, String filename, Int32 channel, Int32 countryCode, Int32 tuningType, Boolean useStreamingEngineIfAvailable, Boolean previewMode, Boolean fmRadioMode, Boolean fmRadioPreviewMode)
   at GBPVR.Backend.Common.DirectRecordingSource.startRecording(IRecordingSourceConfiguration config, Int32 qualitySetting, String filename, ChannelTuning channelTuning, Int32 minutes, Boolean useStreamingEngineIfAvailable)
   at GBPVR.RecordingService.x93f60a55016d55c4.xcba1f05fb5a46d5f() 


[nia]

Just revalidated: I can change to all the channels in the config-application and see them in the tiny tuning window.

So at least GBPVR is aware of them and 'sees' them in some way. So the problem must be somewhere in the area where GBPVR takes the raw tuner signal and creates a recording file.

Is this a MUX issue?

[nia]

Currently GBPVRRecordingService.exe-native.log is growing wildly - approx 10MB/min. It's adding this line as fast as it can:

2007-03-29 01:20:35.937 VERBOSE GetFilterProperty - IKsPropertySet->Get propertry failed

Pretty scary growth rate for a log-file :eek:

/Niels

[sub]

Does the PVR350 record ok if its the first/only thing recording after restarting the recording service?

[nia]

It did until this evening. Now it don't.

All recordings that's currently being initiated only create the folder for the recording and the folder jpg.

[sub]

What does FilterCheck output if you run it now?

[sub]

Did you confirm my question above? You logs show a DVB recording starting before the PVR350 recording.

[nia]

This is getting reeeealy weird.

I went back to the Microsoft MUX. I have the 350 as the primary device (in the top both in recoding status and in config).

Now - recording on common channels actually DO initiate a DVB-recording (and not a 350 recording as it should). But now the DVB actually records :confused: (and trust me - I have been using the MS-MUX before with no recording success.)

Well - after 3 minutes of recording, the machine froze entirely. But that may be related to a MS upgrade notice: If I wanted to upgrade to MediaPlayer 10, when I played one of the in-progress recording just to see if anything was getting on 'tape'.

Now the GBPVR system has rebooted. I will switch machine and do a FilterCheck.

[nia]

Filtercheck log attached:

[sub]

Sorry, I dont really know.