Dvico FusionHDTV DVB-T Plus Problems

[nodrog]

I have been using my Dvico FusionHDTV DVB-T Plus and it's native program for a year or so and finally decided to upgrade to some better software. I installed both MediaPortal and GB-PVR and had an immediate preference for GB-PVR. However I'm having a few difficulties with my Dvico.

Under BDA Device Config if I check the 'Only show devices detected on this machine' I get 'FusionHDTV5 RT Gold (ATSC)' Fiddleing around with that I manged to get an EPG up an running and scan some channels. I have the same problem I've seen other users have that I can only scan the last channel i watched in the Dvico native software, however, I can also only watch the last channel through GB-PVR! And if i reset the computer and run GB-PVR then i just get a whole lot of blank channels until i run the Dvico native software, then i get one

Back to the drawing board I had a look through the forums and found the problem I'd had above. I got onto on Graphedit and changed my BDA.ini

[Dvico Fusion DVB-T PLUS]
TUNING_TYPE=DVB-T
FILTER_TUNER=FusionHDTV, BDA Tuner1
FILTER_CAPTURE=FusionHDTV, Transport Stream Capture1
PIN_TUNER_IN=Input0
PIN_TUNER_OUT=MPEG2 Transport
PIN_CAPTURE_IN=MPEG2 Transport
PIN_CAPTURE_OUT=MPEG2 Transport

As it turns out this is the same as the FusionHDTV5 RT Gold (ATSC) except for the tuning type being ATSC vice DVB-T.

Unfortunately with the BDA device set to my new Dvico Fusion DVB-T PLUS setting I still get a whole lot of nothing. If i try to 'Map digital channels...' It comes up with the error 'GB-PVR was unable to start the BDA device... check the config...' And If I try to run Live TV it simply fades to black for a second then returns to the main menu. At least with the ATSC i get one channel... sort of!

Any help? I'm In Australia btw. Thanks in Advance!

[sub]

Unfortunately with the BDA device set to my new Dvico Fusion DVB-T PLUS setting I still get a whole lot of nothing. If i try to 'Map digital channels...' It comes up with the error 'GB-PVR was unable to start the BDA device...

If you get this then your bda.ini settings arent correct. Can you run filtercheck then zip and attach the filtercheck.log? http://forums.gbpvr.com/showpost.php?p=1...ostcount=6

[nodrog]

Cheers

Filterchecklog attached.

I'm using the latest Dvico drivers and GB-PVR 1.0.16 btw.

[sub]

Hit the 'map digital channels to epg channels' button, then zip and attach the config.exe.log and config.exe-native.log and I'll take a look.

[nodrog]

Config logs after hitting the map digi channels button.

Thanks again.

[sub]

Its a bit hard to tell looking at your logs, but it looks like you've either currently got it set as a ATSC device in bda.ini, or previously tried scanning with an ATSC device selected.

Try deleting any .cache files in the c:\program files\devnz\gbpvr\bda directory, then try again.

[nodrog]

Brilliant!

Nothing at all in my c:\program files\devnz folder, but I deleted the scan1.cache in c:\program files\gbpvr\bda and it's currently scanning and it's picked up 80% of the channels so far!

Thanks very much!

[nodrog]

Had GB-PVR 1.0.16 running sweet on my HTPC for over a month, tried to update to 1.1.5 and it's all gone bad.

I lost my live TV and couldn't re-scan channels anymore.

I have tried every combination of uninstalling and re-installing 1.0.16, 1.1.5, .net 2 and microsoft runtime with no luck.

Now when I load the config and try to 'map digital channels' I get a couple of errors - "Fatal Error - installation corrupt - please re-install NERO" and then it seems to start scanning but seconds later I get an "aplication error" and GBPVR config quits.

Logs attached, any help appreciated!

Cheers