Fresh installation, unable to start device

owilsky · 2012-10-02, 08:05 PM

Also happy to help, but I am away from my machine at the moment, will send logs asap.

***sub*** · 2012-10-02, 08:29 PM

Can you try to scan with this patch, then post the npvr.log? It wont work, but hopefully the logs will help.

(I'm just heading out for an hour or so)

trummel · 2012-10-02, 08:53 PM

It may not be what you expected Sub, but with the modified unmanaged.dll, the scan ran. I didnt change anything else, I promise. Just to prove it, after I had copied the log, I put the original unmanaged.dll back and scanned again, with the same failure as before.

Logs from both runs are attached.

owilsky · (This post was last modified: 2012-10-02, 09:17 PM by owilsky.)

I can confirm, with the new dll it suddenly works. Smile

Attached the logs from FilterCheck and npvr. I cancelled the channel scan after a few seconds, I hope that's enough for the log.

Thanks for your incredible fast help!

owilsky · 2012-10-03, 05:08 PM

OK, channel scan does work now, I setup all my channels and the EPG. But when I want to start LiveTV all I get is

Code:
unable to find available capture device

Attached the log.

owilsky · 2012-10-04, 09:22 AM

OK, after looking at the log it's obvious that you need the other files too ;-)
So here's NPVR.log, NRecord.log, ndigitalhost-20.log and ndigitalhost-21.log.

Looking at the ndigitalhost log files I see that the "ConnectPins failed: hr = 80040217" message is there again.

Any ideas?

Kind regards,
Oliver

owilsky · 2012-10-05, 01:57 PM

I will start a new thread with this new problem as the subject has changed, has nothing to do with channel scanning.

***sub*** · 2012-10-05, 05:22 PM

owilsky Wrote:I will start a new thread with this new problem as the subject has changed, has nothing to do with channel scanning.

It's still the same problem, so I've deleted your other thread.

See if this patch helps.

owilsky · 2012-10-05, 06:04 PM

Weird. I tried the new dll and only get a freeze while NextPVR says "...please wait...". Logs are attached. But now I get the same results with the patched dll from earlier above, also a freeze and only two log files, not four as before...

***sub*** · 2012-10-05, 06:19 PM

It looks like your nrecord.exe isn't starting due to a socket already being in use. Try rebooting.

Possibly Related Threads…
Thread		Author	Replies	Views	Last Post
	Unable to access tuner after hibernation	bm_00	1	1,299	2022-12-12, 02:00 PM Last Post: mvallevand
	Device Update - Channel Mapping	chezmorris	10	4,928	2022-07-01, 01:59 PM Last Post: mvallevand
	All my recordings start 90 sec early	ncsercs	2	1,443	2022-03-19, 03:28 AM Last Post: sub
	device needed for recording	David209	2	1,814	2021-04-04, 08:47 AM Last Post: David209
	Need help with unable to find capture device please?	Deandar1	2	1,769	2021-01-29, 07:17 AM Last Post: sub
	unable to delete recording	manic_biker	9	2,961	2020-12-01, 09:41 PM Last Post: mvallevand
	Problem with 1 device and 1 frequency	lost@c	6	2,180	2020-08-21, 04:11 AM Last Post: lost@c
	Need help with unable to find capture device please	thebigz	5	3,482	2020-06-15, 02:05 PM Last Post: mvallevand
	unable to communicate with recording service	MaxOne72	9	3,555	2020-03-07, 11:59 AM Last Post: Graham
	Unable to find capture device	Rich A	2	2,086	2020-03-06, 10:39 PM Last Post: Rich A