With the death of yapi2xml, I was recommended mc2xml as a replacement. I like it though I heavily used the remapping tool of yapi2xml. Does anyone have a way to remap channels using mc2xml? (or any xmltv for that matter)
I tried using the "Channels" tab in config.exe and though it seems to put the channel in the correct order in the guide, it doesn't change the display name.
I looked into writing gawk scripts, but that seems beyond my abilities.
directv -port COM2 -baud 9600 -set NEW -box D10100 *6
I get the following output:
Code:
Setting DSS Box Type: 0 (RCA)
Setting DSS Command Hex Set to: 0 (NEW)
Setting DSS Command Hex Set to: 0 (NEW)
Setting DSS Box Type: 1 (D10100)
Setting channel: 6 (00-0x06-0xff-0xff)
Sending Key: 0
Settings:
Port: COM2 Baud: 9600 Box: D10100 Retries: 0 Hex Command Set: NEW
Open port to receiver
Openning Command Start: 0XFA ...SUCCESS
Sending Command: 0XA5 ...SUCCESS
Sending Command Data [00 0X01 0XE0]...(command wrote (3 bytes) status [0x1])...SUCCESS
Sending Command Complete: 00 ...SUCCESS
Reading Reply Status For Command: (valid status [0xf0])...SUCCESS
Expecting to receive In Process Reply For Command: (received [0xf2])SUCCESS
Reading Command Status: ...(read status 0xf4)...SUCCESS
Sending Key: 0
Openning Command Start: 0XFA ...SUCCESS
Sending Command: 0XA5 ...SUCCESS
Sending Command Data [00 0X01 0XE0]...(command wrote (3 bytes) status [0x1])...SUCCESS
Sending Command Complete: 00 ...SUCCESS
Reading Reply Status For Command: (valid status [0xf0])...SUCCESS
Expecting to receive In Process Reply For Command: (received [0xf2])SUCCESS
Reading Command Status: ...(read status 0xf4)...SUCCESS
Sending Key: 6
Openning Command Start: 0XFA ...SUCCESS
Sending Command: 0XA5 ...SUCCESS
Sending Command Data [00 0X01 0XE6]...(command wrote (3 bytes) status [0x1])...SUCCESS
Sending Command Complete: 00 ...SUCCESS
Reading Reply Status For Command: (valid status [0xf0])...SUCCESS
Expecting to receive In Process Reply For Command: (received [0xf2])SUCCESS
Reading Command Status: ...(read status 0xf4)...SUCCESS
Sending Key: select
Openning Command Start: 0XFA ...SUCCESS
Sending Command: 0XA5 ...SUCCESS
Sending Command Data [00 0X01 0XC3]...(command wrote (3 bytes) status [0x1])...SUCCESS
Sending Command Complete: 00 ...SUCCESS
Reading Reply Status For Command: (valid status [0xf0])...SUCCESS
Expecting to receive In Process Reply For Command: (received [0xf2])SUCCESS
Reading Command Status: ...(read status 0xf4)...SUCCESS
Clearing On Screen Display
Sending Key: clear
Openning Command Start: 0XFA ...SUCCESS
Sending Command: 0XA5 ...SUCCESS
Sending Command Data [00 0X01 0XF9]...(command wrote (3 bytes) status [0x1])...SUCCESS
Sending Command Complete: 00 ...SUCCESS
Reading Reply Status For Command: (valid status [0xf0])...SUCCESS
Expecting to receive In Process Reply For Command: (received [0xf2])SUCCESS
Reading Command Status: ...(read status 0xf5)...FAILED
Failed to send dss command
Clearing Data Port: .SUCCESS
Any ideas to why it won't change channels? I can power off/on, channel up/down, but I cannot directly change channels.
My COM Port settings are as follows:
Bits per second: 9600
Data Bits: 8
Parity: None
Stop Bits: 1
Flow Control: None
Use FIFO Buffers: Enabled
Receive Buffer: 1 (Low)
Transmit Buffer: 1 (Low)
Any help would be greatly appreciated. Also, is there anyway we can get the EXE updated with the latest script found here: http://www.pdp8.net/directv/directv.shtml
As it has some new features (setup_channel_sd_hd), which I would like to use. I can try out the Perl script itself, but I'd like the simplicity of this EXE.
inside movie wizard...when i have my movie highlighted and press play on my remote it plays the next movie in the list not the one selected. to play the move i have selected i have to press "ok" to go into the details of the movie then "ok" again to choose watch. any ideas?
Release Version : 01-17-081204-15-POP-402-000 (full update)
Release Date : 05 December 2008, 19:40 +8GMT
Quote:Comments :
1. New NMT apps 00-17-081204-15-POP-402
2. Fixed faded color for jpeg at 360-deg rotation 3. Video bookmark:
- 10 bookmarks available now
- Press stop to bookmark the last video playback
- Press enter / play with focus on bookmarked clip to resume
4. Fixed "check disk" interrupt handling
5. Fixed recovery kernel no red screen displayed
NMT APPS
Release Version : 00-17-081204-15-POP-402
Release Date : 05 December 2008, 19:45 +8GMT
Quote:Comments :
1. Minimum firmware version to use this NMT App is 01-17-081127-15-POP-402-000
2. Fixed sometimes unable to access casgle web ui
I'm having a problem with my HVR3000 running on DVB-T and Vista 64bit ultimate, where when I try to watch live tv I get a System.Access ViolationException.
I also have another problem, with inprogress recordings, but plays fine once recording is completed, but this problem can wait.
Both C5 US and C5 life crash GBPVR every time I go to watch them. As soon as I hit play from the TV guite the PVRX2 has encountered a problem box pops up and a few moments later I can see the no signal popup from gbpvr behind it. I couldn't see anything in the logs but the windows "what does this error report contain" mentions psiparser.ax
[ATTACHMENT NOT FOUND]
repeated the problem this morning and the logs seem to have more errors this time
[ATTACHMENT NOT FOUND]
Channel 28 is WGN out of Chicago. It has always shown up in Config in "edit recording source" as "28 WGNSAT", and has worked fine.
Lately, the EPG shows no programming info, but hte channel still works. I open the EPG XML file and see teh name has changed to "28 WGNAMER" for the display name in the format I have been using.
In config I tried "Update EPG", but the name did not change.
How do I get teh new name to go into GBPVR so I get the correct listings?
Really love the new Multi-Record option for recording same frequencies, but When im using both my tuners it seems to always choose the incorrect one to use. For instance if I'm recording one show and at the end of it I have two new shows to start, the tuner always seems to select the multi-record to the show that doesnt share the stream. Is there some way I can tell GBPVR which tuners to use for specific shows?
