I have been running peer to peer networking since the dos days & never had much problems (apart from one batch of network cards that had the jumper config printed on the card that was wrong) but since two different clean installs (on two different computers) of the 20021/22 w10 (over the last year) & both of them not always being visible to each other, more often not visible than visible yet mostly always visible by my old NextPVR server which is running w10 upgraded from a long(ish) time installed w7 install I am just about at my wits end. I have spent hours with google search & tried a heap of stuff about network discovery but all to no improvement.
I run NextPVR v4.2.5 on a Windows 10 machine. I can access live TV fine using the NextPVR client on the host machine, but I can't access the live TV stream from VLC Player on another Windows 10 machine on the LAN.
I'm using this as the network stream URI in VLC: http://192.168.1.230:8866/live?channel=1
VLC doesn't report an error, but it doesn't connect to the video stream (I just get the scrolling orange bar in the status bar at the bottom).
I have the web server option enabled on the NextPVR host machine, on port 8866.
I have explicitly allowed both the NextPVR program and port 8866 through the Windows firewall on the NextPVR host machine, and have no other AV software installed on that machine.
Hello,
I have time on my hands again due to being winter here and I would like to revisit the idea of creating a IPTV channel from my IP Camera. I Have found this item on line and think this is what I need or should I continue researching the use of ffmpeg? Keep in mind I am not a computer genius just know enough to make me dangerous. Below is the item I found on line plus a couple videos I found using ffmpeg with xampp software.
Just trying out NPVR and android TV after years of Kodi+TVheadend. I've sideloaded the app on to my Sony x95G Android TV but I can't progress from the Installation Information Version 1.2.1 screen. When I choose 'select server' I don't have any servers available but NPVR is setup, running and I'm able to watch streams from the webclient. I have a pincode set in application access and access over the internet ticked... A manual configuration doesn't connect either.
Everything is fully wired between the devices so no wireless issues or subnet issues to worry about...
Am I missing something really obvious like a go button that is not showing??
I've finally setup NextPVR on to my NAS using docker and I have to say its still a wonderful piece of software, especially with the NZ IPTV streams.. solves my issue of no UHF arial and no HD from our Satellite streams. Next issue is to setup the client on my Android TVs (Nvidia Shields and Sony TVs). I used to use Kodi with TVheadend and it worked fine and wondered what the native client does that Kodi doesn't?
I'm not concerned about the cost, I'm happy to contribute to the costs of developing systems such as this but wanted to know if I'm better just 'contributing' rather than buying the app?
Probably more of a linux question but after changing my headless Ubuntu 20.04 server to a static ip address the old address is still offered as an alternative to the fixed address in the NextPVR app on my apple TV 4k. I can swipe it away but it immediately reappears. To ease the pain for my technophobic family how can I remedy this so that NextPVR app launches directly to menu?
I cannot get subtitles for live UK TV. The 'Subtitle Stream' box allows selection of English(DVB subtitles) but the (Apply&Restart) button doesn't seem to do anything but halt the display for a short while, and checking later it still shows None. Am I missing something? I have the current version 5.2.5229111.
Running NPVR on an Intel NUC with a HDHR Quatro, win 10, NPVR windows client to view recordings.
Had to do a fresh set up of the HDHR on Saturday due to UK Freeview changes (plus I updated the HDHR firmware) and since then I have been experiencing early termination of recordings. The client shows no errors and the correct start and end times but the files themselves are short. The files play correctly.
For example, I have just recorded two programs that were scheduled for 13:00. They both started OK but failed with a length of 6:58 so at around 13:03 as I have 4 minute pre-pad set. The programs show in Ready Recordings as 12:56-13:34 and 12:56-13:49 and no errors. The HDHR log for the period shows:
20220131-12:56:06 Tuner: tuner0 tuning 1 BBC ONE W Mid (t8dvbt:514MHz-4165)
20220131-12:56:06 Tuner: tuner0 streaming http to 192.168.1.202:49798
20220131-12:56:06 Tuner: tuner1 tuning 2 BBC TWO (t8dvbt:514MHz-4287)
20220131-12:56:07 Tuner: tuner1 streaming http to 192.168.1.202:49799
20220131-13:18:42 Tuner: tuner0 http stream ended (remote closed)
20220131-13:18:42 Tuner: tuner1 http stream ended (remote closed)
I do not have sufficient knowledge to figure out if the error is with the HDHR, the network, the PC or NPVR (or anything else) so would appreciate any help/advice that can be offered and if I have omitted any information that might be needed, my apologies.
Trying to install PNVR 5 on WIn10. It halts with message Cannot connect to Local Host.
Starting NVPR Client results in a box with System.ArgumentException followed by many lines of code. I cannot copy this box. It seems that the the server has not been generated? I have tried with Edge and Firefox with the same result in both case.
Version 4 , installed under Win7 continued to work with the upgrade to Win10. This was deleted before I tried to load version 5
Your Help would be appreciated.
Gilroy
I have nextPVR running on an Ubuntu 18 (Bionic) headless Mac Mini server using a WinTV-dualHD tuner. I successfully remotely setup all available DVB=T channels and EPG using Chrome running on a Mac running on the home network. I can watch TV and schedule recordings on the Mac. The server is also accessible from my iPhone using the NextTV app.
However although the LG smart TV I wish to watch TV from can access the NextPVR web page with its TVOS browser but none of the tuned channels are evident and the devices page cannot be selected on the setup tab. What am I missing?
