I've been running a GBPVR server for a good while and it's been going well. I've tried the client mode, but I've run into a few problems.
I installed GBPVR and set it to Client Mode, Streaming, and set the paths to point to the server.
On the client, I can see the list of recordings and the TV guide, but I can't view anything (likely because they are DVR-MS which I know won't work in Client mode).
However, if I go to the Video or Music Libraries, I see the root of the local machine, not the server. I was under the impression setting the client to streaming would automatically take care of that?
Similarily, the System menu tells me the space on the hard disk drive of the client. I don't know, is that normal?
The whole install seems a bit flaky and slow, which is wierd cause the server is very slick and stable.
What decoders does it use when your mapping your digital channels? Does it use the same ones that you have saved in your playback tab?
My video looks great when im mapping the channels but when I actually go to watch them full screen they are so choppy that it is unwatchable. Is it possible that while im mapping it is using different decoders then when im watching full screen?
Second question. Would having a radio antenna within 200 yards effect my over the air HD tuning via Antenna?
Anyone know why not able to access the settings on v1.2.13 on the main menu? Each time I try clicking on the settings and it just pop back out to the main menu. Another problem I encountered is the switching tv channels with direct press on the numerical keys on the remote does not work. I can only go by using channel up and down key. Anything i can do in configuration file? Thanks.
I'd like to sort and tidy my recurring recordings but since I have a lot this is hard using the PVRX2 interface. Can someone point me in the direction of the database engine, or is the GBPVR database proprietary?
When you watch the video, the blue triangle comes up when I hit the channel up key, it goes blank when GBPVR says stop, and then there is the 8 second delay while the PCH player initializes before the actual buffering happens.
Of note these are two 1080i AC3 QAM channels down converted to SD as input to the same HVR 1600 card. So the MVP couldn't do this at all.
Finally got my act together and upgraded from 1.1.5 to 1.2.13 this morning. Noticed that the name/number of the channel in the guide is now only the name of the channel. Compared both GBPVR.db3 files, in this table they are the same
for example
name = 60 AETVP
channel_number = 60
display_name = AETVP
is GBPVR 1.2.13 now using the display name?
is there an option to concantonate channel_number and display_name to give an updated display_name? If the above is the case.
am testing digiguide using xmltvgui to grab the listings and the xml produced looks fine in XMLTV EPG Viewer (40 channels or so) but GBPVR only gets 16 when pointing to the data.xml.
not sure why this is and also, GBPVR doesn't display any program information either...
I have one sat channel TV8 mont blac that is causeing pvrx2 to crash as soon as i try and change to it.
I've been playing with MDplugins, but this channel is unencryped so i'm not sure if its related.
logs attached.
On a slightly different note, im using vplug for a couple of sat channels (TT 3200 budget) but its a bit odd the MDAPI doesnt seem to start if I select a sat channel form the tv guide on the main menu, however if I am on terrestrial (Nova T 500) and i channel surf to a sat channel vplug fires up fine...odd....
I am running 1.0.16 and have tried to upgrade to 1.2.13 but had problems when I replaced the gbpvr.db3 file with my old one. I am guessing there was a change to the database. I have a large number of recordings in the database that I don't want to lose. How can I upgrade the database file? I would happy to incrementally upgrade to 1.2.13, but where can I find the interim releases? If they are not available, is there some sort of script I can run?