Hi Im getting this message in logs .. recordings bomb out 3 mins or so into recording.. googled the message and not found

"Found expired lease. Stopping recording"

Rec Logs attached .
This recording yielded 2 files
:file 1 - Grand Designs Waterloo_20070621_18051900.mpg 14640 kb
:file 2 - Grand Designs Waterloo_20070621_18051900-2.mpg 46286 kb

if I record in non-mpeg , they still fail , some interference here.
TIA for any help..
Just abt got the setup nailed, but rec is pi... me .
cheers Pete

the main web page shows some forum content that mer mortals can't get to. such as
sub: v1.0.4 (19 June)
@ 21/06/07 by sub
just thought i would let you know.

When using timeshift mode and when watching recorded shows, my skip ahead button will send the recording backward approximately 3-4 minutes. It will then work normally skipping ahead 60 seconds (I have skip ahead set to 60 sec and skip back set to 5 sec). During this the timeline will move ahead the time that it has skipped back. By the time I finish a 1 hour show the timeline will show approximates 1 hour 50 minutes out of 1 hour. This is also the case if i go directly into the directory and mouse over the file. It will say the duration is 1 hour 50 minutes even though it is a 1 hour show. Everything seems to work fine after the initial skip back using the skip forward button. Any ideas what may be causing this.

AMD 4600+
2Gb DDR2
ATI Radeon 1950Pro
HDHomeRun (Qam Mode)
GBPVR 99.12
ATI Video Decoder
Microsoft Mediacenter Remote
DVR-MS Mux

This may or may not be the right place for this problem, but since this is the main function of the PC, here goes: In the past week or so, I've been having problems when the PC tries to hibernate. It will attempt to hibernate and when it turns most of itself off, it immediately turns back on. For the life of me I cannot figure out what is causing it to turn back on the second it hibernates. I haven't updated any software during that time and I don't have wake on lan turned on. The only thing I've done is completely unplug everything and move the pc from one side of a desk to another and plug everything back in. I can't see that anything related to that would be causing this problem. I've run out of things to try and I am hoping I can find a solution among the knowledgeable folks here.... I am using this PC with gbpvr 99.12 and also the mvp. I turn off the mvp whenever I'm not using it.

Hey guys I am going to China to study the language and am trying to decide whether or not to take my PVR. My video card can output S-video and RCA.

I know the standards are PAL D there so I shouldnt have any problems... right?

Just thought this warranted a sticky heads up to the users of Zap2It Labs EPG.

They have announced the service will cease to exist on 9/1/2007. :eek:

This could be a marketing ploy to introduce a subscription fee.....but it is anyones guess.....:confused:

Here is the link to the Zap2It Labs Forum Thread. You will need to log in with your Zap2It is/password.

Had a bit of rain last night. My camera at home caught me coming up the drive with my recycling bins just and a lightning flash went off behind me.

Cool HUH!! To be fair to Wellington, I can't remember storm like this for years!!

Hi,

After setting up a new-build XP system with a Nova-T 500 Dual Channel card, I`ve spent about an hour scanning both devices for all the channels, and then had to wait until after 7pm to get BBC3 and BBC4 etc.

Now that both devices are setup and are unlikely to ever use another ariel feed, can I backup the channel data / frequencies so that in the event of a new software installation I can simply copy the files back and I would not
need to go through the scans again for either device ?

If this is possible, where are the files located please ?

Cheers,

Highlander

Have been searching the wiki and the forum and googling around but can not find the answer.

Can GBPVR use the MCE Standard Front Panel Display?
Mine is a HID device presumably from Tatung with Sw coming from intel and it is described by an XML file as

I have been using GBPVR for the past couple of years, and think it is a fabulous program. (I hope it survives the Zap2it issue!).
In all that time, I have been struggling with playback issues, with the VMR9 Custom being my best option but still at what I consider 95% quality (with minor stuttering on full screen pans and during OSD). I was starting to think it was a hardware limitation! (And yes, I have the dx9.0b quartx.dll and any other tuning tweaks I could find.)
Then I tried VMR9 FSE. I get all the eye candy of VMR, and the smooth pans of overlay. This is what I have been looking for!

However, it is not without its issues.
1. I can no longer use net radio. This is a primary function for me. It does not crash, and I can just back out of that menu and everything is fine. It just does not react, it doesn't show the connecting text at the bottom or start the music stream. Does it have something to do with the visualizations? I think sub said something about those and FSE. I don't care for those anyway, so if there is a way to eliminate them so net radio works again that would be great. I am using the standard "Blue" skin.
2. Upon exiting GBPVR, I lose the desktop completely. The GBPVR menu gets painted over the desktop so I cannot see anything, and I do not know how to force a screen refresh. Restarting the computer using the hardware power button is currently my only way to recover.

If anyone has any ideas (especially for net radio), I would really appreciate the help.