After several months of working npvr wont connect to Hauppauge dual tuner, this after the update.


  logs-20200427-1514.zip (Size: 114.01 KB / Downloads: 1)

Hi,

I'm using a Raspberry Pi 2B and Raspbian. I used the deb file to install NextPVR and I've had no problems there. I can log on to the web interface and it can see my Xbox One TV tuner. I select the right region (in my case UK-SuttonColdfield) and click scan channels, but it never actually finds anything. 

I tried TVheadend and it picked up the channels, so I'm not sure what I'm doing wrong. 

I've been trying to get this working, but I'm close to giving up, although I have found it satisfying troubleshooting and install OS' and things like that and I've learnt a lot more about Linux so it's not been a complete waste of time.

Jamie

Hi - I gave up on EPGs as they are not reliable, therefore decided to program NextPVR for manual recording.

If I have show that is 2.5 hr. long, is it possible to put a time to start and end recording at specific time and recur the same.

I see I can use the software with EPG and do the same, but without EPG it is not.

Thanks for your help. I love the software though, it is the very best!

also, if you have good EPG providers, please let me know as well.

thanks

I had a recurring recording timer set and subsequently deleted it.

It did not cancel future recordings. Now, about 10 instances show up daily that fail, but I am tired of seeing them in the recording queue.

They do not appear in either Kodi nor NPVR under recurring recordings, but they show up in both under scheduled future recordings.

I would be willing to just cancel all recordings, then rebuild the recurring recording selections if need be.

Any help will be greatly appreciated.

Hiya.
I am running Kodi 18.6 and NextPVR 5.0.3.200415 on the same machine.
I am using a HDHomeRun Connect Quattro with firmware 20200225

When in TV Guide within Kodi... when I select a channel and then choose switch.. I get a timer along the bottom which shows how far the current program is in to the program. But it doesn't open the channel.
Whilst checking NextPVR device status, it shows nothing in use and the same on the HDHomerun web interface.
It can take 3-5 times (or more) of selecting the channel and selecting switch before it finally opens.
when it does, it then shows 3 items



And then once I refresh it just shows one active



However it only shows one tuner active in HDHomeRun



I've enclosed the logs, but password protected it. I'll PM sub with the password

If you check from 00:21:25.566 - that is where it first mentions BBC News, which is the channel I was trying to select.

Any ideas why it take a few attempts to open any of the channels?

Cheers :-)

Attached Files

  logs-20200427-0023.zip (Size: 1.26 MB / Downloads: 4)

Hoping someone can help. I have the SDK 3.1 Runtime installed and trying to run the following command to test changes in the database. But nothing gets changed. Is this the correct syntax to use to rename files in the database.

I'm trying to create a script to rename files with no SXXEXX so Plex can see it.

dotnet "C:\Program Files\NextPVR\NScriptHelper.dll" -Rename "G:\NextPVR Recordings\NHL Hockey\NHL Hockey_20200426_15301700.ts" "G:\NextPVR Recordings\NHL Hockey\NHL Hockey - Episode 4-26.ts"

I appreciate any help.

I am having a recording issue where the computer doing the recording will typically drop two or three seconds once or twice during a 90 minute or two hour movie. It is not a huge loss, but I'm trying to build a movie library, and the drop outs are noticeable and annoying. Moreover, the dropouts are not present in the same movie when I watch it while it is recording (i.e., the stream from the satellite dish is fine - the computer / NextPVR is dropping the recording periodically). The computer setup is a Windows 7 pro computer (I backed this down from Windows 10, which removed some but not all of the problems), a Colossus 2 card, and a connection via HDMI to a Dish Network STB. Any help in fixing this would be greatly appreciated. I've got two computers with close to the identical setup, and both are experiencing the same issue.

Thanks very much!

The main exe is a much older build.  Did I download the wrong version?  Where is the newer build?  It is showing Direct 2D, not 3D

I still can't find HAUPBLAST.EXE in V5.  Forgive me if I just don't see it and tell me where it is.  For us old V4 users, no big deal since we have it, but it appears to me that it's still not in the V5 installation.  I'm not sure how to get V5 working with Hauppauge tuners without Haupblast.

In the last version , when you paused you could then hit Timeline and the timeline would go away so you could see things under it, such as weather stats.  You can no longer make the timeline go away in pause.