I am not sure how to go about describing this, but I'll give it a shot.
I have another issue (yes I have quite a few recently), I am not sure whether I did something wrong or something changed in 4.2.1.
A while back, I had re-mapped a block of channels (about 9 of them) to a different set of channels numbers. Whenever I wanted to watch one of those channels, I selected the re-mapped channel number and watched away. But today, I have noticed that when I select one of those channels to watch, I get the dreaded "tuner not available" message. For whatever the reason, I am not able to tune to those channels (on HDHR Prime). This was the first time I tried one of those channels, since I updated the server on Thursday, so I am not sure if it something change embeded in 4.2.1 or something I did to screw it up. This issue is present on the kodi client, nextpvr client and server running nextpvr frontend.
It appears that issue affects only that block of channels, other re-mapped channels seem to work fine. It seems that npvr has lost the association of the re-mapped channels and their tuning information.
How did I screw up? Is there a way of fixing this?
I did try deleting the affected channels, and then rescanned to add those channels back, but this didn't seem to help.
The HDHR software plays those channels fine, as does VLC - so it's not the channels or the Prime, something else.
Help!
The attached log file contains the info from trying to tune to 4 of the 9 channels on the server using nextpvr in standalone mode.
How do I properly configure the NPVR Emby plugin? I have the NPVR standalone software running on Win 10. I can access my LIVE TV M3u playlist via local or remote browser. I have entered the same IPORT info in the Emby Plugin settings. However, the Emby NPVR plugin is completely empty when I open it. I make sure that the guide is running. They just don't seem to be connecting based on my Emby server log.
Picture quality is fine usually for the first hour. But then at around the 1h mark, the video quality starts degrading with intermittent pixelations and jumps that increase in frequency and pretty much make the video unwatchable by the 2 hour mark. This is from the recording because it is still there at the same locations when I use different software to rewatch the video. This hasn't always been the case and I have had videos that go for 3 hours that have been perfect. That doesn't happen anymore and now consistently degrades after 1 hour.
I just installed a new DVB-S dual tuner card, in device setup I scanned channels for the first tuner and set it up with 4 instances of multidec plugin. The second tuner I just answered Yes to copy the setup. But the four plugin directories in MDPlugins did NOT get created for the second tuner even it had set decrypting to multidec and instances to 4. After entering setup and exiting on that tuner the directories were created ok.
Is there an easy way I'm missing to delete a whole series? Say I want to delete all episodes of "Fast N' Loud" the tv show. I usually use the web interface table view and select the episodes individually using a find on the page.
Hello,
Today around 6am CST I had live TV freezing. It was on the entire system. I had two android boxes running kodi at the time. I was watching ATSC channel 2.1 on both boxes. I suspect it was the off air channel causing the issue. Perhaps someone can look at the logs for me? I would appreciate it.
Thank you,
Bruce
I followed the instructions for installing the TV listings in the proper directory, however, when I go into settings and try to add a guide I get an "Unhandled Exception" error.
I'm not sure how to get past this error. Anyone have any ideas?
I'm away from home now, in a hotel room with my TV box and a keyboard (no remote), and I can't see a way to Delete recordings.
I thought at one point I saw a Delete icon as part of the recording info, but now all I see is Resume and Watch.
ORT info in the Emby Plugin settings. However, the Emby NPVR plugin is completely empty when I open it. I make sure that the guide is running. They just don't seem to be connecting based on my Emby server log.
