Is it supported by 1.4.7? Im not getting the channel logos to show up. THey are the exact same name, as the channel (for example 39 History or 109 WITIDT i shouldnt have to append the .jpg file extension should i?
I recently purchased a Hauppauge 1250. i plugged it in, pressed the power button, and the computer had a long beeeep. no video, no boot. When i remove the card, computer boots fine. What's the problem here? Yes, i have it in a PCI-Express slot. The computer i'm using is one i home built. What's going on??
Whenever I turn on my pc after a cold boot I get only a black screen when I click on Live TV. The strange thing is that this only happens when my pc has been off for a while.
If I go to config to check if my tuners are picking up the channels I can see the channels working.
If I bring my computer back from hibernate this doesn't happen.
Hi,
Is there any way to configure GBPVR to show right to left content (Hebrew) as excepted ? I mean align to right and not align to left.
I mean to the EPG data for a specific TV program etc'...
Just in the last couple of days I'm seeing poor/jumpy recordings. The picture freezes up for a second frequently, stops and starts, but the sound is fine - until you get futher into the recording. It just gets worse the longer you watch. Playback is fine on older recordings. I restarted the computer only a few days ago and it's gone longer without a restart previously.
The total space in the recordings directory space available is 381GB of which I've used about 104GB, so probably neither of the two drives is full yet (not sure how Windows actually uses the space).
Could this be something to do with dynamic spanned disks being used as the recordings folder .. or maybe it just needs a defrag? It has been perfect up til now.
First, I apologize for not scouring the Forum for this answer but I'm in a time crunch and hopefully will get a reply soon.
I'm looking for away to create a manual timed recording from a Microsoft WPF application. I don't need the GB-PVR GUI only the Recording Service. What my WPF app is going to do is to create the recording, wait for it to start recording, then playback the recording using the WPF media control. This will run on a Windows 7 computer with a Hauppauge encoder. I tried this with MCE and everything worked except the WPF media control does not playback any sound from the WTV file so I'm hoping I can get it to work using GB-PVR and MPG files.
In case you're wondering, this app is a digital sign that encompasses a live TV feed in the middle.
So i just got myself a new hauppauge 2250 for my new computer. WinTV can display the channels. I pulled the listings which is a 4 meg file with show info. I mapped the channels in config.
I believe I have the mux's setup correctly. The channels are enabled.
In the attached logs I see that it sees the shows.
2009-10-07 21:52:53.901 VERBOSE [4] - channel 26.1 WVENDT : 261 shows
2009-10-07 21:52:53.901 VERBOSE [4] - channel 27.2 WRDQDT2 : 334 shows
However when I click on tv guide it does not enter the guide. When I click search it is blank.
Man, had everything going well, until I added a second hauppauge wintv 1950 tuner.
Device manager sees both tuners, but when I plugged in the second tuner, the first tuner only receives static. Cable input is as good as always.
Swapped tuners (both usb) and got video back on one tuner (while keeping the second one unplugged) for the time being.
Then I decided to just delete all the capture sources and start from scratch. Both tuners plugged in, added the first tuner (in capture), 1950QAM, went to digital mapping section, it can't detect any channels.
I'm fried for the night, I can't even get one of these suckers to work let alone two. I did have one working with both plugged in at one point, but just can't seem to get both working.
Also re-installed the drivers on the disk that came with the tuners. I've rebooted and started the capture source from scratch. No go.
