If I go to the EPG and want to watch the live tv stream of a program I'm recording the only way to do it is to choose a program on a channel next door, get live tv going then channel up or down to the channel the program I want to watch is on.
Would be nice to have a "play" and a "watch now" button in the EPG
I updated my ffdshow filters (to ffdshow tryouts revision 2527) to solve another problem recently and now I can no longer play *.mkv files. I've attached my zipped config.xml and logs...can anyone see what I need to change to be able to play these files again?
I have a strange circumstance that causes PVRX2 to use almost all processor...
- Schedule a recording, record the show, comskip is run after the show is done.
- Go into PVRX2 and everything is fine, processor-wise. Can look at the recording, tv guide, etc...
- When you go to live TV, processor usage goes up to 100% and live tv starts (delayed for a while because the processor is busy) then all you get is frame updates every couple of seconds.
Shut down PVRX2 and restart the recording service, start Live TV again. Works fine. Start a recording, then cancel it so it doesn't complete. Everything is fine.
Not sure if it is comskip causing the problem or what else it could be.
For the last several days, Ultra has not run properly (gets started but hangs indefinitely). Today I tried it a few times manually and get the same effect plus the error message below when it hangs up. I've attached my logs, the current XMLTV.XML file, a screen shot of the error dialog. Any suggestions as to what is causing the problem and how to fix it?
************** Exception Text **************
System.ArgumentOutOfRangeException: Index was out of range. Must be non-negative and less than the size of the collection.
Parameter name: index
at System.ThrowHelper.ThrowArgumentOutOfRangeException(ExceptionArgument argument, ExceptionResource resource)
at System.ThrowHelper.ThrowArgumentOutOfRangeException()
at System.Collections.Generic.List`1.get_Item(Int32 index)
at UltraXMLTV_Enhancer.frmMain.DoEnhance()
at UltraXMLTV_Enhancer.frmMain.btnXMLTV_Go_Click(Object sender, EventArgs e)
at System.Windows.Forms.Control.OnClick(EventArgs e)
at System.Windows.Forms.Button.OnClick(EventArgs e)
at System.Windows.Forms.Button.OnMouseUp(MouseEventArgs mevent)
at System.Windows.Forms.Control.WmMouseUp(Message& m, MouseButtons button, Int32 clicks)
at System.Windows.Forms.Control.WndProc(Message& m)
at System.Windows.Forms.ButtonBase.WndProc(Message& m)
at System.Windows.Forms.Button.WndProc(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.OnMessage(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.WndProc(Message& m)
at System.Windows.Forms.NativeWindow.Callback(IntPtr hWnd, Int32 msg, IntPtr wparam, IntPtr lparam)
************** JIT Debugging **************
To enable just-in-time (JIT) debugging, the .config file for this
application or computer (machine.config) must have the
jitDebugging value set in the system.windows.forms section.
The application must also be compiled with debugging
enabled.
When JIT debugging is enabled, any unhandled exception
will be sent to the JIT debugger registered on the computer
rather than be handled by this dialog box.
This is the setup I am trying: WHS running GBPVR and a WinTV PVR150MCE card that I borrowed from a MCE2005 machine to try. The client is a PCH which will display the gbpvr using mvpmcx2.
I am still trying to get past the VMR9 error on the WHS server itself but have not tried to solve it because my main goal is to have the WHS in a closet and use PCH next to TV.
I am trying to figure out how to use the MCE2005 USB IR blaster in the WHS with GBPVR. I do not really need to control GBPVR using the remote on WHS. Only via the PCH remote via the network.
However, I do need the GBPVR to change channels using the MCE2005 IR blaster on the comcast cable box and this is where I am stuck. I have tried to work through the full HipGuide on the wiki but the Testing IR codes does not seem to send anything over the blaster. If I only need GBPVR -> HipSend -> HIP -> IR blaster to work. Is there any easier way? Is there any other easier way without needing HIP?
With a WinTV HVR4000 card can you use the DVB-T tuner and the DVB-S tuner at the same time with GBPVR?
I currently use 2 X nova t500's and was going to install another fella but was looking at digital satelite with DVB-T combined.
This is a minor change to Guide.aspx to show the coloring guide without leaving the page. It now shows in a dropdown when you mouse over "Coloring Guide" and hides it again when you mouse out. To keep with the current convention, I placed the small javascript in the public folder.
There are two files to be placed in the web folder:
Guide.aspx
public\ColorCoding.js
ColorCoding.aspx* should not be necessary after this change.
I am trying to boot my mvp from a linux box, then get it immediately into emulation mode and connect to gbpvr on a windows box.
(This is a tweak I am trying to speed up the process of starting the mvp - it works fine if I get the linux box to start the windows machine, then serve dongle.bin etc from gbpvr, but this all takes time)
The mvp boots up fine (see linux log below) but for the life of me I can't seem to get the config file served to the mvp. All that happens is it gets stuck at the mvpmc main menu. If I then hit emulation mode it just cycles through the startup process and goes back to the main menu.
I have the config file in /tftpboot, also in a directory /mvpmc (all world readable and writeable) but neither seems to work. Do I need to tell atftpd to look in a particular place for the config file?
The default values are true, but if they were set to false, would GBPVR attempt to add channels that may show up in, for example, Win TV from Hauppauge but wouldn't normally show up in GBPVR digital scan?
