Hi,
I am building an Optiplex GX280 for a friend. It's a fresh install of Windows XP, all updated and GBPVR prereq's installed. It's a P4 3.4Ghz with 2GB RAM. I'm familiar with the capacitor issues these optiplexes have had, but the tops of all the caps in this machine appear to be dead flat and the symptoms aren't consistent with that problem (I suspect that rules bad caps out, but admittedly, you never know). Berfore putting the 9600 in, while doing all the updates and installations etc along with many restarts, it was running perfectly.
I was at the point where GBPVR was installed and runs, but I was having trouble getting the TV picture working nicely / at all. Not too concerned about that yet - I think that's just a matter of playing with mux's and settings etc.. I know that part of things is often a bit tricky (although I did expect to have fewer problems than I did on my own PC, but, oh well ).
The plan was always to get a better graphics card with the thought that graphics performance wouldn't be a problem after it was installed and software was tweaked, and that it might even make all the above problems magically go away. The idea is that with the better graphics component than the integrated one, it will play movies, TV, photos and music etc without missing a beat. I still think (hope) that is the case, BUT...
I just put a new Gigabyte NX96T512HP (a 9600GT) into it. It now blue screens pretty reliably the first time I boot it up after the AC power has been disconnected for a while. It then restarts and the system says it can't see the SATA hard drive. Usually the next time I boot it up manually it's fine, though it seems to be getting slightly flakier over time eg. MMC console crashed this time when I went to look in the logs.. Nvidia system tray didn't load..
When the blue screen happens it's too fast to see the text, it just restarts immediately .. is there anything I can do about that?. The only thing in the logs is Event ID 14, Source "nv", Text: "Unknown error on" .. and that's it!
I occasionally hear a slight, quiet squeal which I think is the hard drive (it almost sounds like a muffled, shortened, system speaker beep, it's so quick), so it does kinda look like the drive could be the problem, but it definitely wasn't doing any of this bluescreening rubbish before the 9600 went in. I have downloaded the latest drivers from Nvidia and updated the BIOS.
I have connected the extra power cable supplied with the card ... is it likely to be a power supply problem? I have another hard drive sitting there which I could try instead, so will try that. I wondered if it would be worth rebuilding Windows with the 9600 installed this time, rather than adding it later .. ?
I am using the latest version of burndvdx2 in GBPVR v1.2.13 with PAL and imgburn set in the config.
I select a recorded film with comskip data to convert to iso, select 16:9 format, com trim, verify that the skip points are correct, select a menu picture in edit and hit the iso button.
The system creates an iso but has used ADDDVDNTSC.cmd and has ignored the comskip information, so the disk is just the full file.
Any ideas what is going wrong and a possible fix - even if it is editing the buildDVD.cmd - I have changed the NTSC to PAL169 which fixes the format but does not fix the comskip issues.
HI I hope this is the right thread for this question. I have gbpvr set to start at boot. I need HIP to fire up first and then fire up gbpvr. I need hip to be in a run state. Every time I try this hip starts in an edit state. I can do this in a vbscript file. but I can't force HIP to be in a run state. Has anybody conquered this? Any thoughts appreciated.
Has anyone had a lot of luck with UBU and MVPs? I read the sticky about setting it up but I cant get VLC to work. It just throws me back to the main menu in PVRX2 and reboots the MVP.
I did get one link to work using windows media player.
I am running GBPVR 1.2.13. New Install, no plugins.
Latest Nova-T driver v2.122.26109 ment for 90xxx. My card is a 90003 (not the often seen 90002). I had this card working on my old machine (with an older driver, unsure which version exactly).
In config, I have it set up as a Nova-T 90002, Device #1. The 90002 is avaliable when I click show only detected cards.
When I try to scan for channels, I get an error message "......Reason: Failed to locate configured BDA tuner device". I have noted that if I change to device #2 then the error message reads "......Reason: Failed to locate configured BDA capture device"
I have attached the GBPVR logs.
Oh, I should probably mention that ScanChannelsBDA_UK.exe starts up and presents it's menu, but fails fo scan anything. Error message "Failed to connect Capture filter to BDA Demux".
Hi everyone. I have just started playing with this plugin and I am getting alot of it to work on the computer but not much to work on the MVP.
Like this link
mms://tv3.lzu.edu.cn/tv3 - Discovery Channel
I got that link from this website(below) where there are 100's. Some are sponsored and work very easily on the computer. Others have been added by users and can be tricky in Ubu.
I was wondering if it possible to pause the recording of episodes for a timeperiod?
In Holland during the summer there is allways an episode stop. They usually repeat the last season. I know for a fact that Greys anatomy will start on november the third. I would like to pause the EPG programming until the third november for Greys anatomy.
The same goes for Top Gear on the BBC. The new series don't start yet so they repeat the old ones. I would like to set a date so that GBPVR can resume recording the episodes again.
Is there any plugin that can do that or is something of a future option?