I'm in the UK trying to use the on-air EPG for Freeview (works fine with the HDHomeRun application. When I try to update the EPG it scans each channel for about 6 seconds then proceeds to the next channel. The end result is "EPG Update complete. [0 inserted, 0 updated, 0 skipped]".
Hello
I am new user on this platform. I want to ask a question. Is NextPVR is a tv tunning software?. I want to use my pc as a tv too. I have installed tv tunning card in the pc but I have no software to tune the tv channels. How can I tune tv channels.
Kindly guide me if this easy for you to guide.
Regards.
I have installed, re-installed, but it doesn't matter, the app will not run on my phone. I have searched the forum and I find it hard to believe that I am the only one that this is happening to. After trying to open it, it immediately shuts down. If I try 10 -15 times, maybe I can get it work for a bit. It is Android version 10, One UI version 2.1, Kernel version 4.14.117, knox version 3.4.1. I don't know what else you would need to evaluate this problem. Attached are the screens I eventually see from the continual crashes.
Been testing NPVR on multiple systems to see what works best for me. Is there any way to important channels from a linux db to windows database? I tried inserting channels table but that didn't see to work. Any ideas? Thanks!
I have just upgraded from V4 install using a forum guide to copy my config.xml and DB files over to V5.
Everything seems to have worked, and all my channels show up etc, but I am having issues getting IR Blasting working again under V5.
I have a combination of DVB-T NZ channels, and STB channels via set top box, via a Hauppauge Colossus capture card.
In Nextpvr v4, I configured the blaster configuration to use HaupBlast.exe to fire IR signals using the Hauppauge Colossus cards own IR blaster port.
In NextPVR, I found where to enter in blaster settings under 'Device' settings for the Colossus card, but when I select a channel sourced from my STB, no IR signals are blasted.
In my V4 config, the HaupBlast.exe was in my program files (x86) folder, so I just copied that file into the same folder in NextPVR 5.
If I open a command prompt, and navigate to that folder, and type Haupblast.exe 1, it works, and I see my STB change channels, but when I use nextpvr 5 to select channel, I get no channel change.
My blaster config line is 'C:/Program Files (x86)/NPVR/HaupBlast.exe with {channel} parameter.
It seems to have saved the blaster configuration for all the channels, and they say 'Haupblast.exe 1' 'Haupblast'.exe 2' etc etc.
Just found out that I am not able to watch two EXTRA device channels from two different clients at the same time. when Tuning to a second channel while watching one already, NextPVR returns an error immediately (nrecord.log shows a 404 Not found error). However, watching the same channel from two different clients is allowed.
...
2020-07-03 00:51:36.651 [DEBUG][34] [FFMPEG]: [http @ 019ad680] HTTP error 404 Not Found
2020-07-03 00:51:36.652 [DEBUG][34] [FFMPEG]: http://127.0.0.1:8867/live?channeloid=11...dfacf13db7: Server returned 404 Not Found
...
BTW, The issue doesn't exist for over the air channels.
I do not know what happened. I had a working setup and suddenly it stopped working.
There is nothing I can point to and say "I did that" so have no roll back plan. Only option may be Windows updates. <shrug>
When I tried to play a channel I would get a message starting device and nothing beyond that. I went to the settings page and all my channels were still listed. I changed USB ports and Windows pop up indicated successful addition so I tried to set up the new device but it would not find any channels.
In the end I deleted NextPVR and reinstalled. There is now just one DVB-T device and the IPTV listing as well but still no channels being found.
Logs attached.
Hopefully somebody can point me in the right direction.
